I have a 20+ year old GE Wall oven.

Model jkp37g0l1wg

The top oven's baking element just stopped working. I tested it and the element has proper resistance so it's not the element.

I'm assuming it's the oven switch because it's not sending power to the element, which brings me to my next question.

I took the panel off and the 2 switches look completely interchangeable...they both have the same wiring and look exactly the same. However, they have 2 different part numbers, WB22X5143 and WB22X5140.

I'd rather have the top oven than the bottom one so it's not a safety issue for the baby running around. Any idea if I can simply swap these switches out (bottom switch to top oven)? Thanks in advance.

⟐ Answered 4월 14, 2026 at 9:13 GMT-7

⟐ Commented 4월 14, 2026 at 8:53 GMT-7

I'm not sure what just happened.

I cleaned my screen with a tiny bit of water, but I guess there might have been a bit too much. I guess I was pressing down on the cloth to get rid of something in the corner. I've done this many times before without issue, but now there is a huge light blotch in the left corner of my screen. There is an odd rectangular shape near the bottom too that doesn't make much sense. Take a look at this image of a completely white window:

https://i.imgur.com/fp4G5IY.jpg

I've read that the classic rice method, and or heating the computer up for a long period of time might help it dry, but I'm not entirely sure it's only water that's the problem.

Anyways, hoping someone can help me understand the damage I've done and what I might be able to do, other than paying for a replacement :D. Thanks.

Time seems to have healed all wounds.

I ran the computer hot with a 'while true' loop for a couple hours and it burned most of the water off, and what was left is slowly disappearing.

⟐ Commented 4월 14, 2026 at 8:46 GMT-7

The dash went out and has caused...... no speedometer, no gas gage, no heated seats, no cruse control, no manual operation of windshield whippers, and I have to remove the fuse to stop them,no turn signals, although I do have hazard lights and break lights, I do have headlights but no high beam. Is there any way at all to fix this????

⟐ Answer edited 4월 14, 2026 at 8:38 GMT-7

- Updated BIOS from A08 to A13.

- Replaced the hard drive with a new SSD (tried both MBR and GPT partition styles).

- Swapped and tested individual RAM modules.

- Changed SATA Operation modes (AHCI and RAID On).

- Disabled Intel SpeedStep, C-States, Virtualization, and Multi-Core Support (tested with only 1 CPU core).

- Removed the Wi-Fi card, DVD drive, and all other peripherals.

- Replaced the CMOS battery and performed a hard power reset.

When I remove the RAM entirely to test the motherboard, the laptop does NOT beep. Instead, the fan spins at high speed, and only the Battery and Wi-Fi signal LEDs blink. Is this a confirmed motherboard failure, or is there a specific power rail or chipset issue common to the E6320 that causes this freeze?

⟐ Commented 4월 14, 2026 at 8:31 GMT-7

could i install an sm-g901 display? its has the same processor as mine. just 2 gb ram instead of 3 gb and just FHD / 2k display. if yes, where to get a display.cheep as possible :D

i know that i cant install a sm-g900 display which would result in a bootloop

⟐ Commented 4월 14, 2026 at 8:29 GMT-7

⟐ Commented 4월 14, 2026 at 8:25 GMT-7

⟐ Answered 4월 14, 2026 at 8:21 GMT-7

⟐ Answered 4월 14, 2026 at 7:52 GMT-7

⟐ Answered 4월 14, 2026 at 7:44 GMT-7

I have tried to disconnect all the speakers and the powersupply. Than I waited a few hours and connected only the power and the error still remains.

Does anybody knows how to fix this?

AMP Board:

⟐ Commented 4월 14, 2026 at 7:43 GMT-7

⟐ Answered 4월 14, 2026 at 7:35 GMT-7

⟐ Commented 4월 14, 2026 at 7:12 GMT-7

⟐ Answered 4월 14, 2026 at 7:10 GMT-7