I found mentions of the motor not being properly aligned.

The official FAQ states: The motor might not be in the correct position. Check if the water tank is filled and if the drip tray is in place. Turn the appliance OFF and then ON again. Then simultaneously press the button for My-Coffee and the on/off button for more than 2 seconds. The motor will move into the correct position. Insert the brewing unit again and check that it is correctly locked in position.

However, this proposed solution did not reset the motor position in my case.

I found that the locking handle of the brewing unit moves a metal lever.

This metal lever engages a button in the machine.

By carefully pressing this button (i used the handle of a small spoon), the motor reset to the correct position.

Long story short: I don't have a question, and just wanted to post this here for future reference.

⟐ Commented 5월 11, 2026 at 9:42 GMT-7

⟐ Commented 5월 11, 2026 at 7:53 GMT-7

I have a Frigidaire dishwasher, model FFID2426TS5A that won't force drain or start a cycle. When i apply power, the lights above the buttons all start up green, then the start/cancel light flashes. I try to force a drain (there's a small amount of water in the bottom of the dishwasher) and all lights go out on the button pad, and the dishwasher acts unresponsive until the next time I power cycle. It seems like a control board issue, but given the price of a control board, I would like to be 100% certain before I invest. Is there any way to know for sure?

Thanks, Ivan

⟐ Answered 5월 11, 2026 at 7:53 GMT-7

There is no garbage disposal hooked up to it - no disposal at all.

I took the filters out of the basin prior to ordering the pump in case the issue was a clogged filter but after a good clean there was no change.

The drain hose is not clogged.

It makes sounds like it is draining but when it’s done and I open it up the entire basin (tub?) is full. This is true both before and after the pump replacement.

I’m about to order a pump and motor assembly but I don’t like to just throw parts at things when I’m not sure.

Anyone know what I should do? Is the pump assembly the right move? Is there something I’m overlooking?

Thanks

⟐ Commented 5월 11, 2026 at 7:52 GMT-7

Any suggestions would be greatly appreciated

⟐ Answered 5월 11, 2026 at 7:52 GMT-7

Installed under counter.

Close the door, select cycle, cycle light is on.

Time remaining reads properly.

Start/cancel button does nothing. Trying to push it until display times out and goes blank.

Open the door and pull the machine an inch or so out, then select cycle, cycle light works, time remaining is correct and start/cancel button works.

Push it back in and start/cancel doesn’t work again.

Update: now the 5 cycle lights and the “controls” lights all flash about 2 minutes into a cycle and the machine hangs there.

I’ve done a 5 minute power off reset.

⟐ Answered 5월 11, 2026 at 7:52 GMT-7

This happens to whatever cycle I choose,

Normal wash, Quick wash, rinse only

It just fills up with water and then Turns off,

I have to turn it on again and press cancel to drain the water

I appreciate if anyone can help

Thank you

⟐ Commented 5월 11, 2026 at 7:50 GMT-7

⟐ Commented 5월 11, 2026 at 7:50 GMT-7

⟐ Commented 5월 11, 2026 at 7:50 GMT-7

⟐ Answered 5월 11, 2026 at 7:49 GMT-7

⟐ Answered 5월 11, 2026 at 7:49 GMT-7

Also checked to make sure the keypad wasn't locked and it wasn't. I held down the cancel button for a while and it clicked after a few seconds, still nothing. Tried different button combinations to reset a different way and nothing. Im at a loss unless it circuitry.

⟐ Answered 5월 11, 2026 at 7:47 GMT-7

⟐ Answered 5월 11, 2026 at 7:47 GMT-7

I have a Frigidaire Model# FDB1500LFB0 and my problem is that…

after loading and selecting my cycle and hitting Start, my washer fills with water to the (I presume) proper amount of water in the bottom. The water is very hot. Then the system stops, and the only thing that will happen after opening it after this (anywhere from 3-15 minutes, I did this several times.) is that when the door is shut back and cancel pressed it will drain as normal. It was left to “run” once and the soap drawer opened, dumping the “pod” directly below it. The dishes had never had water on them and the “pod” was mushy from the ambient humidity, and in a spot directly under the drawer. If left on it will cycle through a fill/drain cycle but the spray-arms never move. I have cut the breaker to it on and off with no change.

Any help will be appreciated, thank you.

⟐ Commented 5월 11, 2026 at 7:46 GMT-7

⟐ Commented 5월 11, 2026 at 7:46 GMT-7

⟐ Commented 5월 11, 2026 at 7:43 GMT-7

⟐ Answered 5월 11, 2026 at 7:42 GMT-7

Frigidaire Affinity FAHE1011MWO

⟐ Answered 5월 11, 2026 at 7:41 GMT-7

⟐ Commented 5월 11, 2026 at 7:36 GMT-7