iFixit - Answers With Device "Coffee Maker"

Krups Nespresso XN 2140: There’s not enough coffee extracted.

Fri, 19 Jun 2026 18:47:05 -0700

There’s not enough coffee extracted.

Keurig 2.0-400: Keurig 2.0 will not dispense water and make cofee

Fri, 19 Jun 2026 04:07:48 -0700

it lights up and sounds like its going to dispense water but only a few drops come out

⟐ Answered 6월 19, 2026 at 4:07 GMT-7

DeLonghi ESAM Family: Fuse shuts off when I press the power button of my expresso machine

Thu, 18 Jun 2026 01:28:29 -0700

Hi everyone. I got a problem with my Delonghi micalite Expresso Machine. When I press the power button to turn it on the fuse shuts down and if I try again the same thing happens.

I've done this continuity checkup which I found in another post:

"This is usually caused by the heating element rupturing and shorting to the boiler/casing. You can test for this by removing the top/back of the machine (6 small phillips-head screws) and checking for continuity across the heating element contacts (the two 90 degree prongs sticking out of the top of the boiler). If there's no continuity then the boiler needs to be rebuilt with a new heating element and boiler gasket."

The result was .049, which is good I guess. I attached two pictures for you to check if I've tested the right ends.

Anyone know what's the next step to found the problem?

Thank you!

⟐ Answered 6월 18, 2026 at 1:28 GMT-7

DeLonghi ETAM family: ECAM 450.55 G ELETTA EXPLORE replace Standby-Button

Wed, 17 Jun 2026 14:01:06 -0700

Hi folks,

Does anyone have an idea how I can disassemble the top section of the Eletta Explore?

I need to replace the standby button.

Thanx

Peter

⟐ Commented 6월 17, 2026 at 14:01 GMT-7

Keurig Elite: My Keurig Will not draw water

Sat, 13 Jun 2026 11:38:29 -0700

My Keurig shows out of water but will not draw water from the reservoir

⟐ Commented 6월 13, 2026 at 11:38 GMT-7

Keurig K-Duo: Why too much water?

Fri, 12 Jun 2026 13:34:27 -0700

Keurig k-duo essentials new not measuring right amount of water for pot coffee. Always too much.

Keurig K55: Why is my Keurig Classic constantly turning off while brewing?

Thu, 11 Jun 2026 12:26:35 -0700

I put the Keurig brand K cup in, pull down the top, and press the brew button. It works for a split second then the machine turns off and I waste a K Cup. The K Cup just leaks into my cup and I have to remove it and try again because if I try and use the same K Cup it doesn’t taste right! It happens with numerous Keurig branded K Cups including Hot Chocolate, Cafe Caramel, and Cafe Vanilla. It’s been happening at least 3-4 times a week.

This is my third machine I’ve received from Keurig support and it’s still happening. I’ve done all the needle cleaning, reseting, descaling, and many other fixes. The unit is not even 3 months old.

I’m just at a loss of what to do because I don’t see many people having the same problem. I’m also sick and tired of wasting perfectly good K Cups! Anybody have ideas how to permanently fix this?

EDIT & SOLUTION: I've been able to resolve the issue using a work around. This is not a fix and I don't know why Keurig hasn't fixed it after years of this happening.

When using a milk based K Cup, press it into the bottom by hand so the K Cup is punctured. Pull it up and rotate 90º and close the lid. This gives the K Cup two holes and much less pressure. It has worked perfectly since I've been doing this.

⟐ Commented 6월 11, 2026 at 12:26 GMT-7

Bosch Coffee Maker: How to replace a coupling in a Bosch Coffe machine. Milk frother

Wed, 10 Jun 2026 04:16:42 -0700

I bought the part and I need instructions how to repace it Model TES70129RW10 Coupling No. 00647103. a video will be nice.

⟐ Answer accepted 6월 10, 2026 at 4:16 GMT-7

Jura: Jura Z5 Gen II brew group motor keeps running

Thu, 04 Jun 2026 15:18:51 -0700

The engine that drives the large white gear on the brew group up and down keeps running when the gear is all the way down (obviously accompanied by loud rattling noise).

I disassembled and cleaned the brew group, but it makes no difference. What is used to detect when to stop the motor? I don't see any obvious sensor. Is it simply timed.

Any suggestions how to troubleshoot and hopefully repair?

⟐ Commented 6월 04, 2026 at 15:18 GMT-7

Keurig K10 MINI PLUS: need a owners manual

Tue, 02 Jun 2026 22:26:54 -0700

owners manual for k10

⟐ Commented 6월 02, 2026 at 22:26 GMT-7

Ninja Coffee Bar CF086: Drip stop light prevents brewing

Mon, 01 Jun 2026 05:06:48 -0700

I have a ninja coffee bar, had it for 2 years. The drip stop light lit while brewing, and wouldn't brew at all. I replaced the drip tray, and went away with one brew. Light returns. Seems to occur with unbalanced surfaces too, and whenever we slightly move it or shake it, the light MAY go off and brew for a bit. Has anyone taken one apart and disabled the drip stop sensor, and if so, how?

⟐ Commented 6월 01, 2026 at 5:06 GMT-7

Bravilor Coffee Maker: Bonamat th10 error 12 was tun

Sat, 30 May 2026 01:49:44 -0700

How do i fix error 12 bonamat th10

Jura E8: Heating block overheating and blowing the thermal fuse.

Fri, 29 May 2026 02:18:13 -0700

This morning our Jura 8E tripped the breaker in the middle of the cycle. After resetting the breaker Jura was still dead. Disassembled and replaced the main 15A/250 fuse. Jura powered up then blew a thermal fuse on the Thermoblock Replaced the thermal fuse and it happened again. Tested the thermistor at 112 k ohm. Resistance through the thermoblock was 10 ohms.

When I power up the Jura without replacing the bad thermal fuse it just stays on the “Heating” screen

⟐ Answered 5월 29, 2026 at 2:18 GMT-7

Keurig Elite: water leaking out of bottom

Thu, 28 May 2026 13:04:29 -0700

I just purchased this and it leaks all the water out all over the counter, any idea how to fix. I don't know exactly where it leaks but it empties out at night when I leave water in it.

⟐ Answered 5월 28, 2026 at 13:04 GMT-7

Jura E8: How to fix milk foam

Thu, 28 May 2026 05:19:10 -0700

How to fix milk foam problem

⟐ Answered 5월 28, 2026 at 5:19 GMT-7

Bosch Coffee Maker: Why won’t make coffee?

Mon, 25 May 2026 14:40:44 -0700

Stream wand works but no coffee will come out! Help!

⟐ Commented 5월 25, 2026 at 14:40 GMT-7

Saeco Intelia HD8752: iquid coffee doesn't come out of dispenser instead runs underneath mac

Fri, 22 May 2026 01:11:00 -0700

Coffee beans grind but coffee does not come out of the dispenser instead goes down the back and underneath machine

⟐ Answered 5월 22, 2026 at 1:11 GMT-7

Saeco XSmall: My red and green light is on all the time.

Tue, 19 May 2026 01:51:27 -0700

The red and green light is on all the time. I have switched it off and primed the water, but the machine is just stuck.

Nespresso CitiZ: Leaked after perfereted plate

Mon, 18 May 2026 11:35:49 -0700

Hi,

I have noticed that some of the coffee is leaked into the collector basket. In between the nossle and the brewing unit. I have taken the machine apart and tried to install a new brewing unit but some coffe Is still leaked into the collector basket. I have tried to clean the plate that punctures the pod but still coffee leakage happens. Any idea what could cause this and how I can fix it?

Fredrik

Melitta Caffeo Solo: Brewing unit won't go back in

Mon, 18 May 2026 01:32:11 -0700

The brewing unit of our Melitta Caffeo Solo did not going back in.

I found mentions of the motor not being properly aligned.

The official FAQ states: The motor might not be in the correct position. Check if the water tank is filled and if the drip tray is in place. Turn the appliance OFF and then ON again. Then simultaneously press the button for My-Coffee and the on/off button for more than 2 seconds. The motor will move into the correct position. Insert the brewing unit again and check that it is correctly locked in position.

However, this proposed solution did not reset the motor position in my case.

I found that the locking handle of the brewing unit moves a metal lever.

This metal lever engages a button in the machine.

By carefully pressing this button (i used the handle of a small spoon), the motor reset to the correct position.

Long story short: I don't have a question, and just wanted to post this here for future reference.

⟐ Commented 5월 18, 2026 at 1:32 GMT-7