iFixit - Active Questions With Device "Coffee Maker"

Bravilor Coffee Maker: Bonamat th10 error 12 was tun

Sat, 30 May 2026 01:49:44 -0700

How do i fix error 12 bonamat th10

Jura E8: Heating block overheating and blowing the thermal fuse.

Fri, 29 May 2026 02:18:13 -0700

This morning our Jura 8E tripped the breaker in the middle of the cycle. After resetting the breaker Jura was still dead. Disassembled and replaced the main 15A/250 fuse. Jura powered up then blew a thermal fuse on the Thermoblock Replaced the thermal fuse and it happened again. Tested the thermistor at 112 k ohm. Resistance through the thermoblock was 10 ohms.

When I power up the Jura without replacing the bad thermal fuse it just stays on the “Heating” screen

⟐ Answered 5월 29, 2026 at 2:18 GMT-7

Keurig Elite: water leaking out of bottom

Thu, 28 May 2026 13:04:29 -0700

I just purchased this and it leaks all the water out all over the counter, any idea how to fix. I don't know exactly where it leaks but it empties out at night when I leave water in it.

⟐ Answered 5월 28, 2026 at 13:04 GMT-7

Jura E8: How to fix milk foam

Thu, 28 May 2026 05:19:10 -0700

How to fix milk foam problem

⟐ Answered 5월 28, 2026 at 5:19 GMT-7

Bosch Coffee Maker: Why won’t make coffee?

Mon, 25 May 2026 14:40:44 -0700

Stream wand works but no coffee will come out! Help!

⟐ Commented 5월 25, 2026 at 14:40 GMT-7

Saeco Intelia HD8752: iquid coffee doesn't come out of dispenser instead runs underneath mac

Fri, 22 May 2026 01:11:00 -0700

Coffee beans grind but coffee does not come out of the dispenser instead goes down the back and underneath machine

⟐ Answered 5월 22, 2026 at 1:11 GMT-7

Saeco XSmall: My red and green light is on all the time.

Tue, 19 May 2026 01:51:27 -0700

The red and green light is on all the time. I have switched it off and primed the water, but the machine is just stuck.

Bosch Coffee Maker: How to replace a coupling in a Bosch Coffe machine. Milk frother

Mon, 18 May 2026 23:55:24 -0700

I bought the part and I need instructions how to repace it Model TES70129RW10 Coupling No. 00647103. a video will be nice.

⟐ Answer edited 5월 18, 2026 at 23:55 GMT-7

Nespresso CitiZ: Leaked after perfereted plate

Mon, 18 May 2026 11:35:49 -0700

Hi,

I have noticed that some of the coffee is leaked into the collector basket. In between the nossle and the brewing unit. I have taken the machine apart and tried to install a new brewing unit but some coffe Is still leaked into the collector basket. I have tried to clean the plate that punctures the pod but still coffee leakage happens. Any idea what could cause this and how I can fix it?

Fredrik

Melitta Caffeo Solo: Brewing unit won't go back in

Mon, 18 May 2026 01:32:11 -0700

The brewing unit of our Melitta Caffeo Solo did not going back in.

I found mentions of the motor not being properly aligned.

The official FAQ states: The motor might not be in the correct position. Check if the water tank is filled and if the drip tray is in place. Turn the appliance OFF and then ON again. Then simultaneously press the button for My-Coffee and the on/off button for more than 2 seconds. The motor will move into the correct position. Insert the brewing unit again and check that it is correctly locked in position.

However, this proposed solution did not reset the motor position in my case.

I found that the locking handle of the brewing unit moves a metal lever.

This metal lever engages a button in the machine.

By carefully pressing this button (i used the handle of a small spoon), the motor reset to the correct position.

Long story short: I don't have a question, and just wanted to post this here for future reference.

⟐ Commented 5월 18, 2026 at 1:32 GMT-7

Keurig K-supreme: Where does this black double-hook spring go in a Keurig K-Supreme K921?

Sun, 17 May 2026 15:52:24 -0700

A black double-hook spring, approximately 5/16” in diameter and 3/4” long, fell out of my Keurig K-Supreme (Model K921). I have confirmed it is not part of the K-Cup pod holder assembly.

The handle/lid area seems like a likely candidate, but I cannot see any obvious anchor points or hooks where it should be reattached. Where exactly does this spring belong, and what are the steps to reattach it? Does it require partial disassembly of the head/handle housing to access the mounting points?

⟐ Commented 5월 17, 2026 at 15:52 GMT-7

Cuisinart DCC-3400: Can not set auto to am. I have tried resetting both auto time and do c

Sat, 16 May 2026 20:24:59 -0700

When setting auto time, it will not show am

⟐ Answered 5월 16, 2026 at 20:24 GMT-7

Melitta Coffeemaker: Melitta C35 "Please wait" screen

Thu, 14 May 2026 01:51:31 -0700

Hello everyone,

I am troubleshooting a professional coffee machine (Melitta C35) control board based on the Freescale ColdFire MCF5232CVM100 (BGA package). The system is currently stuck at the initial "Please wait" screen and does not proceed to the main menu.

Hardware Details & Measurements:

· MCU: MCF5232CVM100 (ColdFire V2 Core).

· Flash: cFeon EN29LV160 (TSOP-48).

· Power Rails:

o VDD (Core): Measured 1.6V on the micro-capacitors surrounding the MCF5232.

o VDDIO/Periphery: Stable 3.3V found across the board.

o Analog/Other: 5V rail is present.

· RTC Battery: Measured 3.29V (stable).

· Debug Interfaces: The board provides a standard 26-pin ColdFire BDM header AND a 10-pin (2x5) Mini-BDM connector.

· Service Port: External 9-pin RS-232 (DCE, Female).

Symptoms:

1. On power-up, the display initializes and shows "Please wait".

2. The board has a Reset button that toggles the 3.3V line, but the MCU remains in the same "Please wait" state after reset.

3. I measured -5.6V on the TX pin of the RS-232 port, which indicates that the line driver is powered and the UART is likely initialized by the bootloader.

Questions for the community:

1. Given that the display shows "Please wait", is it safe to assume the MCU has successfully initialized the FlexBus and started executing code from the external Flash?

2. What are the typical reasons for a ColdFire V2 to hang at this stage? Could it be a checksum mismatch in the Flash or a timeout waiting for a peripheral (I2C/SPI)?

3. Does the presence of both 10-pin and 26-pin BDM headers imply any specific debugging priority? Is one more suitable for a USBDM interface to dump the cFeon Flash?

4. Are there any known "trap" states or Double Bus Fault indicators I can check via the BDM pins without a full debugger?

Thank you, Alex

⟐ Answer accepted 5월 14, 2026 at 1:51 GMT-7

Keurig Elite: My Keurig Will not draw water

Tue, 12 May 2026 14:04:50 -0700

My Keurig shows out of water but will not draw water from the reservoir

⟐ Commented 5월 12, 2026 at 14:04 GMT-7

Keurig 2.0-400: Keurig 2.0 will not dispense water and make cofee

Mon, 11 May 2026 07:36:49 -0700

it lights up and sounds like its going to dispense water but only a few drops come out

⟐ Commented 5월 11, 2026 at 7:36 GMT-7

Keurig K-Duo: My Keurig doesn't want to reset after discale

Fri, 08 May 2026 14:29:51 -0700

How can I reset after discale

⟐ Commented 5월 08, 2026 at 14:29 GMT-7

SiFENE KC101: Parts - baskets for ground coffee and basket for tea

Tue, 05 May 2026 11:05:48 -0700

Where do I find parts (baskets)

Keurig Coffee Maker: I made a cup of coffee. Now the lid won't open. It's stuck.

Mon, 04 May 2026 13:44:30 -0700

I made a cup of coffee. Now the lid won't open at all. It's stuck.what should I do?

⟐ Commented 5월 04, 2026 at 13:44 GMT-7

Keurig 2.0-400: How to install replacement keurig 2.0 upper needle gasket 400 series

Sun, 03 May 2026 09:30:23 -0700

Any graphics or illustrations available to show proper installation

DeLonghi ETAM family: I have a rivelia that does not remove the puck

Sun, 03 May 2026 06:21:59 -0700

I have a rivelia that does not sweep the used puck away. Any help would be appreciated.