iFixit - Answers With Device "Jura"

Jura E8: Heating block overheating and blowing the thermal fuse.

Fri, 29 May 2026 02:18:13 -0700

This morning our Jura 8E tripped the breaker in the middle of the cycle. After resetting the breaker Jura was still dead. Disassembled and replaced the main 15A/250 fuse. Jura powered up then blew a thermal fuse on the Thermoblock Replaced the thermal fuse and it happened again. Tested the thermistor at 112 k ohm. Resistance through the thermoblock was 10 ohms.

When I power up the Jura without replacing the bad thermal fuse it just stays on the “Heating” screen

⟐ Answered 5월 29, 2026 at 2:18 GMT-7

Jura E8: How to fix milk foam

Thu, 28 May 2026 05:19:10 -0700

How to fix milk foam problem

⟐ Answered 5월 28, 2026 at 5:19 GMT-7

Jura Impressa C E F Modelle: Pump works, water level goes down, but coffee grounds are dry

Tue, 10 Feb 2026 00:40:10 -0700

Pumps water onto try, grounds stay dry , no liquid out of the spouts

⟐ Answer edited 2월 10, 2026 at 0:40 GMT-7

Jura: Changing Water supply from direct to tank

Sat, 17 Jan 2026 07:30:38 -0700

Hi all!

So, i just bought a Jura Giga 7Xc professional Coffee maker second hånd for my company. Previously it has been connected to direct Water supply - but it also has the funktion to supply Water from Watertank. However Jura has told me that i need to send it to the to have it reprogrammed - can that be real? Is there no way for me to access this menu to Change it?😄

If i just start it with power connected to it, it will keep telling me that the machine is filling no matter what i press..

⟐ Commented 1월 17, 2026 at 7:30 GMT-7

Jura Capresso IMPRESSA J5: Why "Empty grounds" allert is on but there are any grounds

Sun, 14 Dec 2025 01:58:38 -0700

Why "Empty allert" is on but there are any grounds in tray

Jura E8: Jura e8 not rinsing correctly

Sat, 15 Nov 2025 23:59:04 -0700

Hi all,

I have a Jura E8 2021 that’s not rinsing correctly. In the middle of the process it's making noise. I have changed new brewing group with no luck

Jura Capresso IMPRESSA J5: How to replace dispensing faucet

Fri, 17 Oct 2025 18:46:24 -0700

Hi - one of our dispensing faucets needs replacing and I can't find specific instructions online. Can someone direct me to a video or instructions with pictures so I can do it myself? Ordered the part, just need instruction on how to replace it. I know it should not be too hard, just don't want to make it worse. Thank you!!!!

⟐ Commented 10월 17, 2025 at 18:46 GMT-7

Jura: Where can I send my jura coffee machine to be repaired?

Fri, 10 Oct 2025 09:02:27 -0700

where can i send my jura coffee machine to be repaired. it will not grind the beans

⟐ Commented 10월 10, 2025 at 9:02 GMT-7

Jura E8: Service manual? Full tear-down?

Thu, 25 Sep 2025 05:59:57 -0700

I am having a hard time finding the service manual for this thing. Has anybody found one or know where I can buy one?

⟐ Answered 9월 25, 2025 at 5:59 GMT-7

Jura E8: Leaking water at bottom front right corner

Thu, 18 Sep 2025 14:38:20 -0700

What is the source of this leak, and can it be repaired?

⟐ Commented 9월 18, 2025 at 14:38 GMT-7

Impressa A9: How to remove the cover plate?

Sun, 31 Aug 2025 14:18:45 -0700

Hello,

is there a tool or a trick to remove the cover plate.

It is too slippy to make it rotate counter clockwize by hand.

Thank you

⟐ Commented 8월 31, 2025 at 14:18 GMT-7

Jura E8: Screen not working, unintelligible message.

Sat, 30 Aug 2025 05:58:50 -0700

The screen on my is not working. Any suggestions?

Jura Capresso IMPRESSA J5: Coffee, water is fine but no milk/froth

Sat, 30 Aug 2025 02:08:53 -0700

Hi,

I recently got a j9.3 that has been on a shelf for ten years. It had an electronics problem that was resolved by changing the logic board. It has made 6000 cups in total.

I have gone over everything including a stuck backflow valve in the water pump. It seems to run just fine except it doesn't suck any milk either for just milk or foam. It does however pour hot water fine through the same spout. I have taken the ceramic valve apart and checked it over but no wear or tear. Since it can direct water to the brew group and to the water/milk spout it does operate except for the steam that seems to go to the brewgroup that steams like crazy.

Checked all valves and motors.

Any ideas?

/Jan

⟐ Commented 8월 30, 2025 at 2:08 GMT-7

Jura: Can I convert a 220v Jura C60 to 110v so I can use in America?

Tue, 29 Jul 2025 19:46:08 -0700

I would like to know if a Jura C60 can be converted from 220v to 110v

Thank you

⟐ Answer edited 7월 29, 2025 at 19:46 GMT-7

Jura Impressa F50: It's saying drip tray not fitted

Wed, 02 Jul 2025 02:39:26 -0700

It was pulled apart and put back together a screw was misplaced and now it's saying drip tray not fitted error, unsure where the screw went or came from just know that 1 is missing. What screws missing could cause this error directly?

⟐ Commented 7월 02, 2025 at 2:39 GMT-7

Jura: Jura E8 Fill Water Tank

Mon, 16 Jun 2025 00:40:06 -0700

My new Jura E8 is telling me to Fill the water tank. My tank is full. I don't see where my tank has a float in it. I have tried removing the filter and reinserting it. It will not allow me to do anything.

⟐ Answered 6월 16, 2025 at 0:40 GMT-7

Jura Capresso IMPRESSA J5: Aged mother poured water into the coffee bean grate, will it recover?

Wed, 28 May 2025 10:22:34 -0700

She poured ~2 1/2 cups water. I've got every possible hatch open and have used lots of paper towels in the inside, and a rack underneath for air circulation. Can the machine survive this? Can the wires/motor withstand having been drenched? I'm afraid to plug it back in.

⟐ Commented 5월 28, 2025 at 10:22 GMT-7

Jura Capresso IMPRESSA J5: The machine just doesnt power up anymore.

Sun, 04 May 2025 02:44:59 -0700

No lights or nothing after plugged in and power on. Is there a fuse? Where should I begin in troubleshooting the board?

⟐ Answer edited 5월 04, 2025 at 2:44 GMT-7

Jura ENA micro 9: ENA 9 Brew Group problem.

Wed, 30 Apr 2025 08:31:20 -0700

How the Brew Group on ENA 9 micro is supposed to work?⏎
It stays stuck on top upper position and then motor just keeps grinding the cogs. ⏎
I followed disassembly instructions and removed and cleaned the Brew Group.⏎
A also read instructions how to disassemble the Brew Group itself. They sonud pretty complicated. ⏎
I want to understand HOW exactly the motor is stopped when Brew Group ends at top dead position. I do not see any mechanical or electrical sensors. ⏎
I also try to understand how replacing the seals can help.⏎
I can manually screw Brew Gruoup from up to down dead position. All parts seem to move. How the cycle keeps repeating?

Jura Capresso IMPRESSA J5: Jura J5 Won't dispense coffee or water , but runs

Thu, 24 Apr 2025 19:01:45 -0700

My Jura J5 does not dispense coffee or water, but runs. It collects in the tray instead. What can I do to fix it?

⟐ Answered 4월 24, 2025 at 19:01 GMT-7