<![CDATA[iFixit - Active Questions With Device "Kitchen Appliance"]]> https://ko.ifixit.com/Answers/Device/Kitchen_Appliance/All?rss=yes en-US Thu, 09 Jul 2026 01:17:41 -0700 <![CDATA[Whirlpool Microwave: Plus d alimentation No power]]> Plus d alimentation

Translation French - English

No power

⟐ Commented 7월 08, 2026 at 17:23 GMT-7

]]> https://ko.ifixit.com/Answers/View/963158/Plus+d+alimentation+No+power https://ko.ifixit.com/Answers/View/963158 Wed, 08 Jul 2026 17:23:14 -0700 <![CDATA[Whirlpool Microwave: Microwave oven no power at all, but next day it works normally]]> No light, no control panel, no spinning ... nothing ! Like it was unplugged. Next day is working normally, and then stops again.
Fuse , thermostat, door switches checked and are OK. Capacitor and magnetron was not checked, but on the days it works it heats up the food normally.
Any idea ?
Whirlpool MW201

⟐ Answered 7월 08, 2026 at 8:12 GMT-7

]]> https://ko.ifixit.com/Answers/View/895529/Microwave+oven+no+power+at+all,+but+next+day+it+works+normally https://ko.ifixit.com/Answers/View/895529 Wed, 08 Jul 2026 08:12:23 -0700 <![CDATA[Ninja Coffee Makers: Ninja CE201 size and type of screws on bottom plate]]> Hi,

I need to open the bottom of my unit so that I can clean or replace the plastic tubing. Does anyone know the type and size of screw for this unit? I've tried all my hex screws, but I apparently don't have the right bit. Thanks.

⟐ Answer accepted 7월 06, 2026 at 16:48 GMT-7

]]> https://ko.ifixit.com/Answers/View/761764/Ninja+CE201+size+and+type+of+screws+on+bottom+plate https://ko.ifixit.com/Answers/View/761764 Mon, 06 Jul 2026 16:48:20 -0700 <![CDATA[Keurig Coffee Maker: Why is my Keuirg not heating water.]]> When I push the power button it start dispensing water with out heating the water

⟐ Commented 7월 06, 2026 at 14:30 GMT-7

]]> https://ko.ifixit.com/Answers/View/374898/Why+is+my+Keuirg+not+heating+water. https://ko.ifixit.com/Answers/View/374898 Mon, 06 Jul 2026 14:30:35 -0700 <![CDATA[Cosori Pro II: won't stay on when basket I pushed in]]> when basket is pushed in light flickers on. then goes off

⟐ Commented 7월 05, 2026 at 7:51 GMT-7

]]> https://ko.ifixit.com/Answers/View/884128/won't+stay+on+when+basket+I+pushed+in https://ko.ifixit.com/Answers/View/884128 Sun, 05 Jul 2026 07:51:55 -0700 <![CDATA[JVM7195SK: No Magnetron Hum Or Oven Light, But Turntable Rotates - GE JVM7195SK6S]]> This over the range microwave doesn't heat food. When started, there is no light on within the oven and no humming from the magnetron but the turntables rotates and the display counts down. The interior light doesn't come on when the door is open. All other functions work: fan, range light, keypad, display.

I've had technicians come out 3 times for the same problem. The first tech said he flicked a relay on the control card. That lasted about 5 weeks. The second replaced the control card. That lasted about 3 days. The third tech is ordering another control card and the door switches, though he said the switches all checked out. It seems unlikely that two different control boards would fail in the same way. What else could be causing this problem? Wiring/connector? Grease getting in? Power quality?

This unit is under a extended warranty, but I'm getting tired of the loss of the unit for multiple weeks waiting for the tech appointment and for new parts to arrive.

Edit: Here's the mini-manual/schematic from GE for this unit.31 7000107 3

⟐ Answer edited 7월 04, 2026 at 8:01 GMT-7

]]> https://ko.ifixit.com/Answers/View/961616/No+Magnetron+Hum+Or+Oven+Light,+But+Turntable+Rotates+-+GE+JVM7195SK6S https://ko.ifixit.com/Answers/View/961616 Sat, 04 Jul 2026 08:01:56 -0700 <![CDATA[lg mj3965bib: Why is it not warming up food?]]> Why is it not warming up food?

⟐ Commented 7월 02, 2026 at 22:25 GMT-7

]]> https://ko.ifixit.com/Answers/View/956827/Why+is+it+not+warming+up+food https://ko.ifixit.com/Answers/View/956827 Thu, 02 Jul 2026 22:25:24 -0700 <![CDATA[Smeg Kettle: How repair SMEG kettle lid?]]> The hinge part is broken, so the lid doesn’t close properly. How can it be repaired or replaced?

]]> https://ko.ifixit.com/Answers/View/962301/How+repair+SMEG+kettle+lid https://ko.ifixit.com/Answers/View/962301 Thu, 02 Jul 2026 21:02:57 -0700 <![CDATA[Black and Decker PowerPro II FP1510: I have black+decker blender model BL 1220 and it's not working what I.]]> I have black and decker blender model BL1220 it's not working for long time.

]]> https://ko.ifixit.com/Answers/View/962294/I+have+black+decker+blender+model+BL+1220+and+it's+not+working+what+I. https://ko.ifixit.com/Answers/View/962294 Thu, 02 Jul 2026 18:25:05 -0700 <![CDATA[Keurig 2.0-400: Keurig 2.0 will not dispense water and make cofee]]> it lights up and sounds like its going to dispense water but only a few drops come out

⟐ Commented 7월 02, 2026 at 5:55 GMT-7

]]> https://ko.ifixit.com/Answers/View/195534/Keurig+2.0+will+not+dispense+water+and+make+cofee https://ko.ifixit.com/Answers/View/195534 Thu, 02 Jul 2026 05:55:29 -0700 <![CDATA[Thermomix TM5: Why the machine not working]]> How can you advance me to repair the machine showing the error c72

⟐ Commented 7월 01, 2026 at 0:09 GMT-7

]]> https://ko.ifixit.com/Answers/View/770325/Why+the+machine+not+working https://ko.ifixit.com/Answers/View/770325 Wed, 01 Jul 2026 00:09:24 -0700 <![CDATA[Ninja Professional Blender 1100 watt: ninja blender has stopped working and flashing red]]> My ninja blender has stopped working and flashing red

⟐ Edited 7월 01, 2026 at 1:42 GMT-7

]]> https://ko.ifixit.com/Answers/View/961975/ninja+blender+has+stopped+working+and+flashing+red https://ko.ifixit.com/Answers/View/961975 Wed, 01 Jul 2026 01:42:29 -0700 <![CDATA[DeLonghi ECAM Series: Why is the autorinse not starting?]]> Hi,

My DeLonghi ECAM 220.22 Magnifica Start is stuck during startup. The automatic rinse never starts.

The issue started after making a coffee. About 5 minutes later, i smelled something burning. The machine became very hot and the plastic support around the thermoblock slightly melted (i checked it).

Now:

  • The machine turns on.
  • The brew group moves.
  • The lights keep flashing while waiting for the auto rinse.
  • No water comes out.

I checked:

  • Hoses are clean and not kinked.
  • No visible blockage/limescale in the thermoblock.
  • Wires/connectors look normal.
  • When disconnecting the inlet hose to the thermoblock, only a tiny amount of water comes out (when I power it back on).

Thanks!

Block Image
Block Image

⟐ Edited by author 6월 30, 2026 at 14:07 GMT-7

]]> https://ko.ifixit.com/Answers/View/961944/Why+is+the+autorinse+not+starting https://ko.ifixit.com/Answers/View/961944 Tue, 30 Jun 2026 14:07:26 -0700 <![CDATA[Slow Cooker: A 100V slow cooker plugged into 220V power socket what to replace]]> A 100V slow cooker is accidentally plugged into a 220V socket what needs to be replaced

⟐ Answered 6월 30, 2026 at 0:45 GMT-7

]]> https://ko.ifixit.com/Answers/View/961787/A+100V+slow+cooker+plugged+into+220V+power+socket+what+to+replace https://ko.ifixit.com/Answers/View/961787 Tue, 30 Jun 2026 00:45:13 -0700 <![CDATA[Ninja Professional Blender 1100 watt: Why is the power light blinking?]]> I plugged my blender in and hit the power button, but when I select a speed or press pulse, it wont blend. The red power light just keeps blinking.

⟐ Commented 6월 29, 2026 at 12:40 GMT-7

]]> https://ko.ifixit.com/Answers/View/262834/Why+is+the+power+light+blinking https://ko.ifixit.com/Answers/View/262834 Mon, 29 Jun 2026 12:40:47 -0700 <![CDATA[Vitamix 5200: Why doesn’t it turn on when I try?…yes it’s plugged in! ha]]> Will not operate in On position at any speed.

⟐ Commented 6월 29, 2026 at 6:17 GMT-7

]]> https://ko.ifixit.com/Answers/View/868508/Why+doesn%E2%80%99t+it+turn+on+when+I+try%E2%80%A6yes+it%E2%80%99s+plugged+in!+ha https://ko.ifixit.com/Answers/View/868508 Mon, 29 Jun 2026 06:17:49 -0700 <![CDATA[Bamix Pro-3 NSFY: Why is it that the motor work but the blades don't rotate]]> Why is it that the motor work but the blades don't rotate

⟐ Commented 6월 29, 2026 at 6:03 GMT-7

]]> https://ko.ifixit.com/Answers/View/863421/Why+is+it+that+the+motor+work+but+the+blades+don't+rotate https://ko.ifixit.com/Answers/View/863421 Mon, 29 Jun 2026 06:03:43 -0700 <![CDATA[Nespresso U: The spout is not moving into the correct position]]> The coffee is going straight into the waste container as opposed to coming out through the spout. It appears that the spout is not dropping down into the correct position. How do you ensure that the spout does drop in the correct position when the mechanism starts?

⟐ Answered 6월 27, 2026 at 1:22 GMT-7

]]> https://ko.ifixit.com/Answers/View/961393/The+spout+is+not+moving+into+the+correct+position https://ko.ifixit.com/Answers/View/961393 Sat, 27 Jun 2026 01:22:36 -0700 <![CDATA[Bamix Pro-3 NSFY: Motor is not working]]> I don't know what happened blender is not working and motor is not working

⟐ Answered 6월 26, 2026 at 21:33 GMT-7

]]> https://ko.ifixit.com/Answers/View/877007/Motor+is+not+working https://ko.ifixit.com/Answers/View/877007 Fri, 26 Jun 2026 21:33:17 -0700 <![CDATA[Mr. Coffee BVMC-SJX33GT: What tools do I need to remove the bottom plate?]]> What tool is used to remove the bottom plate?

⟐ Answered 6월 26, 2026 at 14:18 GMT-7

]]> https://ko.ifixit.com/Answers/View/961318/What+tools+do+I+need+to+remove+the+bottom+plate https://ko.ifixit.com/Answers/View/961318 Fri, 26 Jun 2026 14:18:48 -0700