전원버튼 옆 하얀색 불빛만 off와 on 반복되고,

중앙 열배출구에서 7초에 한번씩 바람만 심하게 납니다.

해결방법이 있을까요?

해당 스팀덱이 꺼지는 ui를 보여주면서 꺼집니다. 하지만

어느정도 시간이 지나고 자동으로 재부팅이 발생합니다.

해당 사항을 수정하기 위해 바이오스 초기화, 스팀덱 os 업데이트

데스크탑 모드의 전원 관리 설정을 변경해보았으나 문제가 발생하고 있습니다.

우선 의심가는정보로는 이어폰이 연결되어 있는 경우 해당 기기를 연결하기 위해

재부팅이 되지 않나 의심하고 있으나, 확실하지는 않습니다.

⟐ Answered 6월 17, 2024 at 8:42 GMT-7

bios 나 데스크탑모드등 스팀을 로그인하기 전엔 정상작동합니다

그러나 로그인을하면 버튼들이 모두 먹통이 됩니다

⟐ Answered 6월 17, 2024 at 8:21 GMT-7

After purchasing a new battery here from iFixit and carrying out the repair, I have no battery icon visible on the device.

When I connect the old battery, the icon is visible again.

Can we agree this must be an issue with the battery? RMA.

Any input greatly appreciated.

⟐ Answered 4월 09, 2026 at 15:55 GMT-7

I've checked the audio in-game, on Steam (Gaming mode), and on Desktop mode. The issue is universal. Bluetooth and 3.5mm hack are unaffected. Speaker channel volumes are equal.

I haven't seen anyone else with this same specific issue though I know audio issues with the SD seem to be rampant. I've tried some simple fixes including the Factory reset which did not help.

Anyone have any ideas?

⟐ Commented 3월 12, 2026 at 10:01 GMT-7

⟐ Commented 3월 10, 2026 at 4:39 GMT-7

I was wondering how I can clean the inside of my steam deck, I never done this before and since I usually use my deck in a very dusty outdoor business, the inside of my steam deck is very dirty.

Thank you in advance for the help!

⟐ Answer edited 4월 12, 2026 at 14:00 GMT-7

Any idea what’s happened?

⟐ Answered 2월 20, 2026 at 8:45 GMT-7

⟐ Commented 2월 20, 2026 at 4:44 GMT-7

⟐ Answered 2월 07, 2026 at 19:52 GMT-7

⟐ Answered 2월 06, 2026 at 9:54 GMT-7

I opened yesterday and can say for sure now it’s the button.

I’m thinking the only way to fix this now is to 3D print another piece

⟐ Commented 2월 04, 2026 at 23:22 GMT-7

⟐ Answered 1월 30, 2026 at 11:40 GMT-7

I have checked the cable and connector multiple times, but I can’t find any damage.

⟐ Commented 1월 26, 2026 at 14:27 GMT-7

DO NOT DO THIS!

You loose your switch then be hung out to dry because there are no boards on the planet for replacement. That piece of METAL will crush that sensor when ever you are not paying attention or someone else picks up your deck and crushes that LB for either the killing blow or having a temper tantrum.

What you WANT to do is balance that bumper back into its floating neutral position by changing the spring. Yeah. the whole bumper is a floater, when your spring is tired (worn out, no oomph in the return) you get a dead head bumper. limp and weak. then you get mad crushing it, and then it stops clicking. and to get the clicking back, lets put metal over tiny portion of rubber and steal. no.

Change the spring. change the spring, change the spring. But, where do i get a spring? Duuh... any kind of clicking pen.

WAIT this is important. They are not you manufacture spec bumper springs. therefore, the onus is on you to correctly install the modified spring at a correct compression and length and diameter. And make sure the spring is a compression spring not an expansion spring. Just, ... compression. <--- squishy.

if you have the finger strength of a 50 year old martial arts veteran and the skin durability of a rhino, like me (i got my strength s another way), you can pretty much craft a good one with your fingers and not need gloves, band aids, eye protection, first aider on site, mom and/ or dad watching, At least wear eye protection PLEASE. a spring will cull your eyeball before you blink leaving you stunned, then panicking, then screaming, then terrors. PPE Personal Protective Equipment learn it and us it. Not a joke.

DO IT NOW! PPE.

So, you've rolled out a spring, with some stretching and twisting. good. Your reference for a good tension is, you guessed it, the opposite side of your device.

The length of your spring should be... not the same as the original. Because it's not an original, i recommend (if you are going to attempt this) starting with your hand made deformity longer than what is needed and clip .5 to 1 spiral at a time. There will be a point where your like this is ridiculous, and you cut more.... and now your spring is no good because it either too short or hasn't the tension you desire. So, 0.5 (ONE HALF, 1/2) to 1 (ONE, WHOLE Measure) SPIRAL at a time. For your sanity and bleeding finger tips cannot do another spring to save their lives.

Dollar Store get a cart fill it with different pens. Maybe you'll get lucky and China has made a pen just for you! I didn't find mine yet, but I'm close.

Here's my question.

When has it ever been a good idea to create higher force ratings in a components spring assembly where the ratings of force are lower than lifting 175ml of fluid?

Never. that's the answer.

CHEERS! this works, well it did for me. Did the same for a trigger to.

JI-HAW AWM E118077 20706 105C 60V 8-Pin

for Left Daughter Board to Main Board Connection

and I cannot find one. is there anyone who knows where to buy this ribbon cable.

⟐ Answered 1월 07, 2026 at 21:34 GMT-7