But … it doesn’t seem to be completely broken, here’s what’s happening:

When I have a call, the person here’s a lot of static noise, but sometimes also my voice, and sometimes the voice is clear enough and there is less static. Does it mean it can still be salvaged/repaired? If so, does any of you know how I could do that?

Thank you in advance to anyone who will take the time to answer me and give me some advice/guidance.

Warm regards,
Charlie

⟐ Answer edited 9월 21, 2023 at 15:44 GMT-7

I tried resetting the iPhone to factory settings, even tried doing a reset/restore in DFU mode, to no avail. I wanna say this is maybe a hardware issue with the display (digitizer/glass) more so than a software issue. She had a case on it from day 1 but did drop it a few times, and even had a small crack on the screen towards one corner, not too bad though.

This being the case, I'm willing to replace the display myself, but before I shell out $100 on a new one, I wanted to see if anybody else experienced this issue and if so, did replacing the display fix the problem?

⟐ Answered 11월 04, 2021 at 16:29 GMT-7

I work at a repair shop and we had an iPhone XR come back with a breakage on the LCD from the inside. Upon inspecting I saw that the Face ID unit, that is not screwed in for whatever reason, was slightly out of place, causing it to press on the back of the screen and making it break. After pushing the sensor back into place and carefully checking that it was still in the correct position before closing the phone, we gave it back to the customer. It is now two days later and the customer is here again with the same problem.

Has anyone had this same issue or can offer any solutions?

Thank you,

Justin

⟐ Answer accepted 6월 23, 2020 at 13:25 GMT-7

Wondering where I might be able to find a screw position map for iphone XR?

Thanx!

⟐ Commented 6월 17, 2020 at 3:40 GMT-7

⟐ Answered 5월 17, 2026 at 9:17 GMT-7

⟐ Commented 4월 21, 2025 at 20:49 GMT-7

Do I need to replace the lightning connector assembly? I cleaned the port quite well so I doubt that it’s dust…

Thank you for the help!

⟐ Answer accepted 11월 13, 2024 at 9:11 GMT-7

My motherboard has a cut in it

⟐ Answer accepted 4월 04, 2023 at 21:47 GMT-7

This was my first phone repair too so I didn’t even think to replace the screen adhesive.

⟐ Answer edited 9월 21, 2023 at 10:56 GMT-7

⟐ Commented 7월 28, 2021 at 2:15 GMT-7

-FaceID is not working anymore. It says “FaceID is not available” when trying to set it up in settings.

-Screen will randomly click and move all over the place. I will have to shut off the screen and wait a few seconds for it to stop. When my phone is locked it will move so much that a “please wait 2 minutes before trying again” security message.

-Tap to wake also does not work. I have to use the side button to unlock it every time. That’s super annoying haha.

Does anyone have any ideas on what could be going on? Thank you for your help!

⟐ Commented 10월 01, 2020 at 11:35 GMT-7

⟐ Answered 1월 04, 2026 at 3:08 GMT-7

It is not recognized, nor starts to charge when connected to a computer.

⟐ Answered 12월 02, 2022 at 11:14 GMT-7

⟐ Answer accepted 2월 24, 2023 at 7:58 GMT-7

Hello everyone,

I have a problem to re-enable True Tone function on the iPhone XR despite copying the serial to the new screen.

My young brother dropped his iPhone XR and made a crack on his front screen. I managed to get a pulled front screen and replaced it. I also transfered the cracked screen's ear speaker with the attached sensors.

After replacement, I turned on the iPhone XR and everything was working, screen, touch, Face ID and ear speaker. Only function that is missing - True Tone.

I used the Qian Li's iCopy Plus 2.x to copy the data, however my cracked screen's cable broke. So I used 3uTools to copy the "Cover Board Number" and paste it in Qian Li computer software ("MtSN").

Qian Li software and Qian Li iCopy Plus device say they both read and wrote the data succesfully. I followed YouTube videos to do this repair.

Unfortunately, it still does not work after writing the data 4 times. Does anyone else have experienced this problem before? Or did I do something wrong?

Thanks in advance and thanks for your time

EDIT Nov 5 '22

QianLi iCopy Plus 2.x - MtSN read of the new screen

PC software 3utools reading of the iPhone XR

I got my True Tone by using JC Repair Assistant. Apparently, the MtSN (cover board number) which 3utools provided was incorrect.

⟐ Commented 11월 06, 2022 at 19:27 GMT-7

⟐ Answered 3월 30, 2022 at 15:01 GMT-7

⟐ Answered 6월 09, 2020 at 6:00 GMT-7

The first time you take an iPhone out of the box, it turns itself on.

How is this implemented? With a light sensor?

⟐ Commented 8월 08, 2019 at 7:40 GMT-7

So I ripped the red circled cord accidentally when trying to open my phone last night to dry it out. Can this individual cord be replaced or does the whole screen have to be replaced/what do I need to do to fix it?

⟐ Commented 10월 12, 2024 at 22:35 GMT-7

I've been using my iPhone XR which has several cracks and recently have been hit by a wave (yes, a very big one that caught me on the beach) whilst having the phone in my pocket.

I immediately turned off the phone (seemed to be working fine at that moment), dried it, put it in a bowl of rice later and left it there for 2 days.

Ever since then however, the phone won't turn on. I've tried holding the power button for longer times, connecting it to the power cable, doing a soft reset (up, down, power for 10+ seconds) - no reaction whatsoever.

As the phone didn't even get that wet, I'm a little bit stunned that it isn't turning on at all.

I wondered if there's anything I can do if maybe I open up the phone. Check for remaining water, replugging back some cables whatsoever.

Has anyone had a similar experience and been able to revive his phone? I would very much appreciate your help then!

Thank you very much in advance :-)

⟐ Commented 10월 02, 2024 at 10:17 GMT-7