메인 콘텐츠로 스킵하기
도움말

현재 버전 게시자: George A. ,

본문:

Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Should be inside the center console, just pull the cup holders up to see if it is there.
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Should be inside the center console, just pull the cup holders up to see if it is there.
AMPLIFIER REPLACEMENT
 
REMOVAL PROCEDURE
1
1
. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located
under
under the hood electrical center.
1
1
. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located
under
under the hood electrical center.
2. Remove the floor console bezel.
 
3. Remove the cupholder.
 
4. Remove the bolts (1) retaining the console to the instrument panel (I/P).
 
5. Remove the console storage bin.
 
6. Remove the center console end panel.
 
7. Disconnect the audio amplifier electrical connectors.
8
8
. Remove the 4 screws retaining the upper console bracket to the lower
console
console bracket.
8
8
. Remove the 4 screws retaining the upper console bracket to the lower
console
console bracket.
9. Move both front seats to the fully forward.
 
10. Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).
 
11. Remove both rear console side panel screws
 
12. Move both front seats to the fully rearward.
 
13. Remove both front console side panel screws (1).
 
14. Disconnect the floor console electrical connector.
 
15. Remove the console assembly from the vehicle.
 
16. Remove the audio amplifier screws (1).
17
17
. Remove the audio amplifier from the vehicle. Hope
Hope
this helps, good luck.
17
17
. Remove the audio amplifier from the vehicle. Hope
Hope
this helps, good luck.

현황:

open

편집 작업: oldturkey03 ,

본문:

Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Check underShould be inside the rear seat oncenter console, just pull the drivers side. there should be a black box and you will needcup holders up to see if it is there.
AMPLIFIER REPLACEMENT
REMOVAL PROCEDURE
1. If equipped with a Bose(TM) amplifier,
remove the coverradio amp fuse located
under the hood electrical center.
2. Remove the floor console bezel.
3. Remove the cupholder.
4. Remove the bolts (1) retaining the console to the instrument panel (I/P).
5. Remove the console storage bin.
6. Remove the center console end panel.
7. Disconnect the audio amplifier electrical connectors.
8. Remove the 4 screws retaining the upper console bracket to the lower
console bracket.
9. Move both front seats to the fully forward.
10. Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).
11. Remove both rear console side panel screws
12. Move both front seats to the fully rearward.
13. Remove both front console side panel screws (1).
14. Disconnect the floor console electrical connector.
15. Remove the console assembly from the vehicle.
16. Remove the audio amplifier screws (1).
17. Remove the audio amplifier from the vehicle
. Hope this helps, good luck.
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Check underShould be inside the rear seat oncenter console, just pull the drivers side. there should be a black box and you will needcup holders up to see if it is there.
AMPLIFIER REPLACEMENT
REMOVAL PROCEDURE
1. If equipped with a Bose(TM) amplifier,
remove the coverradio amp fuse located
under the hood electrical center.
2. Remove the floor console bezel.
3. Remove the cupholder.
4. Remove the bolts (1) retaining the console to the instrument panel (I/P).
5. Remove the console storage bin.
6. Remove the center console end panel.
7. Disconnect the audio amplifier electrical connectors.
8. Remove the 4 screws retaining the upper console bracket to the lower
console bracket.
9. Move both front seats to the fully forward.
10. Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).
11. Remove both rear console side panel screws
12. Move both front seats to the fully rearward.
13. Remove both front console side panel screws (1).
14. Disconnect the floor console electrical connector.
15. Remove the console assembly from the vehicle.
16. Remove the audio amplifier screws (1).
17. Remove the audio amplifier from the vehicle
. Hope this helps, good luck.

현황:

open

원문 게시자: oldturkey03 ,

본문:

Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Check under the rear seat on the drivers side. there should be a black box and you will need to remove the cover. Hope this helps, good luck.

현황:

open