주요 콘텐츠로 건너뛰기
도움말

현재 버전 게시자: oldturkey03 ,

텍스트:

-john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experience) project. Anyhow, the fuse change seems to be straight forward enough, it is behind the control panel.
+john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experienced) project. Anyhow, the fuse change seems to be straight forward enough, it is behind the control panel.
Remove 2 screws from front vent cover and removed vent cover
Remove one screw from top of display
Gently push display panel up about 1/4 inch and tilt the top toward the front.
Disconnect 3 thin gauge Molex connectors
Disconnect 1 heavy gauge connector
Remove screw from grounding wire at bottom of display circuit board
Remove display panel completely
Remove grill from above display area
To the left is a 2 x2 inch square board
Coil, capacitor and fuse block
Remove fuse
Match fuse rating and replace
[image|218141|align=center]
Number 47 on the diagram is the fuse. Hope this helps, good luck.

현황:

open

편집자: oldturkey03 ,

텍스트:

john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experience) project. Anyhow, the fuse change seems to be straight forward enough, it is behind the control panel.
Remove 2 screws from front vent cover and removed vent cover
Remove one screw from top of display
Gently push display panel up about 1/4 inch and tilt the top toward the front.
Disconnect 3 thin gauge Molex connectors
Disconnect 1 heavy gauge connector
Remove screw from grounding wire at bottom of display circuit board
Remove display panel completely
Remove grill from above display area
To the left is a 2 x2 inch square board
Coil, capacitor and fuse block
Remove fuse
Match fuse rating and replace
-[image|218141|align=left]
+[image|218141|align=center]
Number 47 on the diagram is the fuse. Hope this helps, good luck.

현황:

open

편집자: oldturkey03 ,

텍스트:

-john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experience) project. Anyhow, the fuse change seems to be straight forward enough.
+john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experience) project. Anyhow, the fuse change seems to be straight forward enough, it is behind the control panel.
Remove 2 screws from front vent cover and removed vent cover
Remove one screw from top of display
Gently push display panel up about 1/4 inch and tilt the top toward the front.
Disconnect 3 thin gauge Molex connectors
Disconnect 1 heavy gauge connector
Remove screw from grounding wire at bottom of display circuit board
Remove display panel completely
Remove grill from above display area
To the left is a 2 x2 inch square board
Coil, capacitor and fuse block
Remove fuse
Match fuse rating and replace
[image|218141|align=left]
Number 47 on the diagram is the fuse. Hope this helps, good luck.

현황:

open

원문 게시자: oldturkey03 ,

텍스트:

john vrtiak, usually we like to refer questions about microwaves on here. Those things pack a lot of oomph and are not a good DIY'er (unless experience) project. Anyhow, the fuse change seems to be straight forward enough.

Remove 2 screws from front vent cover and removed vent cover

Remove one screw from top of display

Gently push display panel up about 1/4 inch and tilt the top toward the front.

Disconnect 3 thin gauge Molex connectors

Disconnect 1 heavy gauge connector

Remove screw from grounding wire at bottom of display circuit board

Remove display panel completely

Remove grill from above display area

To the left is a 2 x2 inch square board

Coil, capacitor and fuse block

Remove fuse

Match fuse rating and replace

[image|218141|align=left]

Number 47 on the diagram is the fuse. Hope this helps, good luck.

현황:

open