메인 콘텐츠로 스킵하기
도움말

현재 버전 게시자: Kyle Wiens ,

본문:

Eveans,
 
Here are the following steps you will need. Let me know if there is anything else i can help with. The glass panel is held in place by magnets in the rear housing. So follow these steps:
 
1-Lay# Lay display on its back and press clean suction cups in opposite corners on glass panel. I strongly recommends wearing clean, lint-free gloves whenever handling the glass panel, to reduce cleaning required on reassembly.
# Lift Glass panel straight up and off.
# Remove suction cups and slide glass into protective microfoam bag
# Remove 6 T10 screws: 3 on each side of the LCD panel.
# Raise bottom edge of LCD a few inches using black mylar tabs.
1-Lay# Lay display on its back and press clean suction cups in opposite corners on glass panel. I strongly recommends wearing clean, lint-free gloves whenever handling the glass panel, to reduce cleaning required on reassembly.
# Lift Glass panel straight up and off.
# Remove suction cups and slide glass into protective microfoam bag
# Remove 6 T10 screws: 3 on each side of the LCD panel.
# Raise bottom edge of LCD a few inches using black mylar tabs.
 
I strongly recommends wearing clean, lint-free gloves whenever handling the glass panel,Careful! There are 4 cables to reduce cleaning required on reassembly.disconnect.
From Left to right:
* Cable 1. Ambient Temp Sensor
* Cable 2. AIO Video
* Cable 3. LCD Function Interface
* Cable 4. LED Driver (Backlight)
I strongly recommends wearing clean, lint-free gloves whenever handling the glass panel,Careful! There are 4 cables to reduce cleaning required on reassembly.disconnect.
From Left to right:
* Cable 1. Ambient Temp Sensor
* Cable 2. AIO Video
* Cable 3. LCD Function Interface
* Cable 4. LED Driver (Backlight)
 
2-Lift Glass panel straight up and off.

3-Remove suction cups and slide glass into protective microfoam bag

4-Remove 6 T10 screws: 3 on each side of the LCD panel.

5- Raise bottom edge of LCD a few inches using black mylar tabs.

Careful! There are 4 cables to disconnect.(From Left to right Cable1. Ambient Temp Sensor,Cable2. AIO Video,Cable3. LCD Function Interface,Cable4. LED Driver (Backlight)

6-Lift
# Lift LCD panel straight up and off.
2-Lift Glass panel straight up and off.

3-Remove suction cups and slide glass into protective microfoam bag

4-Remove 6 T10 screws: 3 on each side of the LCD panel.

5- Raise bottom edge of LCD a few inches using black mylar tabs.

Careful! There are 4 cables to disconnect.(From Left to right Cable1. Ambient Temp Sensor,Cable2. AIO Video,Cable3. LCD Function Interface,Cable4. LED Driver (Backlight)

6-Lift
# Lift LCD panel straight up and off.

현황:

open

원문 게시자: Steven ,

본문:

Eveans,

Here are the following steps you will need. Let me know if there is anything else i can help with. The glass panel is held in place by magnets in the rear housing. So follow these steps:

1-Lay display on its back and press clean suction cups in opposite corners on glass panel.

I strongly recommends wearing clean, lint-free gloves whenever handling the glass panel, to reduce cleaning required on reassembly.

2-Lift Glass panel straight up and off.

3-Remove suction cups and slide glass into protective microfoam bag

4-Remove 6 T10 screws: 3 on each side of the LCD panel.

5- Raise bottom edge of LCD a few inches using black mylar tabs.

Careful! There are 4 cables to disconnect.(From Left to right Cable1. Ambient Temp Sensor,Cable2. AIO Video,Cable3. LCD Function Interface,Cable4. LED Driver (Backlight)

6-Lift LCD panel straight up and off.

현황:

open