주요 콘텐츠로 건너뛰기
도움말

현재 버전 게시자: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair. This is not a pro quality fix and should not be used as such, but it’s not bad for a home user with this problem wanting to try it.
Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair. This is not a pro quality fix and should not be used as such, but it’s not bad for a home user with this problem wanting to try it.
 
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor on the chassis fails in a unrepairable fashion and that's the end of it. If you can fix it, Epoxy isn’t hard to find and is cheap. To know with 100% certainty it’s sold, check a hardware store like Lowes and Home Depot first. If you can't find it there (or do not live near one), buy some on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. '''Either way, get gloves. Epoxy DOES NOT COME OFF OF SKIN and you have to wait until skin cells die to get rid of it. You only have one shot, so be very conservative; no more then needed and keep it away from the screw hole.'''
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points and it will be like new again. It may not last, but this often works to save a repairable chassis that has minor damage, at the most.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair.
 
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor on the chassis fails in a unrepairable fashion and that's the end of it. If you can fix it, Epoxy isn’t hard to find and is cheap. To know with 100% certainty it’s sold, check a hardware store like Lowes and Home Depot first. If you can't find it there (or do not live near one), buy some on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Either'''Either way, get gloves. Epoxy DOES NOT COME OFF OF SKINSKIN and you have to wait until skin cells die to get rid of it. You only have one shot, so be very conservative; no more then needed and keep it away from the screw hole.hole.'''
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor on the chassis fails in a unrepairable fashion and that's the end of it. If you can fix it, Epoxy isn’t hard to find and is cheap. To know with 100% certainty it’s sold, check a hardware store like Lowes and Home Depot first. If you can't find it there (or do not live near one), buy some on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Either'''Either way, get gloves. Epoxy DOES NOT COME OFF OF SKINSKIN and you have to wait until skin cells die to get rid of it. You only have one shot, so be very conservative; no more then needed and keep it away from the screw hole.hole.'''
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points and it will be like new again. It may not last, but this often works to save a repairable chassis that has minor damage, at the most.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair.
 
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor physicallyon the chassis fails in a unrepairable fashion and that's the end of it. If you can fix it, You canEpoxy isn’t hard to find Epoxy just about anywhere in retail. Check placesand is cheap. To know with 100% certainty it’s sold, check a hardware store like Lowes and Home Depot first. If you can't find it there (or do not live near one), it can be purchasedbuy some on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there tooEither way, get gloves. Epoxy DOES NOT like to come off of skin. Just be careful how much you use; youCOME OFF OF SKIN. You only have one shotshot, so be very conservative; no more then needed and keep it away from the screw hole.
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor physicallyon the chassis fails in a unrepairable fashion and that's the end of it. If you can fix it, You canEpoxy isn’t hard to find Epoxy just about anywhere in retail. Check placesand is cheap. To know with 100% certainty it’s sold, check a hardware store like Lowes and Home Depot first. If you can't find it there (or do not live near one), it can be purchasedbuy some on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there tooEither way, get gloves. Epoxy DOES NOT like to come off of skin. Just be careful how much you use; youCOME OFF OF SKIN. You only have one shotshot, so be very conservative; no more then needed and keep it away from the screw hole.
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor pointspoints and it will be like new again. It may not last, but this often works to save a repairable chassis that has minor damage, at the most.
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor pointspoints and it will be like new again. It may not last, but this often works to save a repairable chassis that has minor damage, at the most.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair.
Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the supporting plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair.
 
The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor physically fails and that's the end of it. If you can fix it, You can find Epoxy just about anywhere in retail. Check places like Lowes and Home Depot first. If you can't find it there (or do not live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin. Just be careful how much you use; you only have one shot.
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair. The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor physically fails and that's the end of it. If you can fix it, You can find Epoxy just about anywhere in retail. Check places like Lowes and Home Depot first. If you can't find it there (or do not live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. If it's intact without further damage, it's a good candidate for this repair. The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the plastic around the anchor physically fails and that's the end of it. If you can fix it, You can find Epoxy just about anywhere in retail. Check places like Lowes and Home Depot first. If you can't find it there (or do not live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
 
The key thing hereproblem is tomany of these fail in a way that's beyond repair without a new back cover. More often then not use so much it will bleed over but also make surethe plastic around the anchor physically fails and that's the end of it. If you use enough to fill itcan fix it, You can find Epoxy just about anywhere in to the point thatretail. Check places like Lowes and Home Depot first. If you can't find it doesn't fail asthere (or do not live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin. Just be careful how much you use; you only have one shot at thisshot.
The key thing hereproblem is tomany of these fail in a way that's beyond repair without a new back cover. More often then not use so much it will bleed over but also make surethe plastic around the anchor physically fails and that's the end of it. If you use enough to fill itcan fix it, You can find Epoxy just about anywhere in to the point thatretail. Check places like Lowes and Home Depot first. If you can't find it doesn't fail asthere (or do not live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin. Just be careful how much you use; you only have one shot at thisshot.
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. In many cases whereIf it's intact without further damage, it's a good candidate for this happens,repair. The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the ABS plastic expandedaround the anchor physically fails and cracked just enough to fail.that's the end of it. If you can fix it, You can find thisEpoxy just about anywhere in retail to the point I'm just going to recommend going toretail. Check places like Lowes orand Home Depot if you have one locallyfirst. If you can't find it there (or do notnot live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. In many cases whereIf it's intact without further damage, it's a good candidate for this happens,repair. The problem is many of these fail in a way that's beyond repair without a new back cover. More often then not the ABS plastic expandedaround the anchor physically fails and cracked just enough to fail.that's the end of it. If you can fix it, You can find thisEpoxy just about anywhere in retail to the point I'm just going to recommend going toretail. Check places like Lowes orand Home Depot if you have one locallyfirst. If you can't find it there (or do notnot live near one), it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
 
The key thing here is to not use so much it will bleed over but also make sure you use enough to fill it in to the point that it doesn't fail as you only have one shot at this.
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points.

현황:

open

편집 작업: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. In many cases where this happens, the ABS plastic expanded and cracked just enough to fail. You can find this just about anywhere in retail to the point I'm just going to recommend going to Lowes or Home Depot if you have one locally. If you do not, it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. In many cases where this happens, the ABS plastic expanded and cracked just enough to fail. You can find this just about anywhere in retail to the point I'm just going to recommend going to Lowes or Home Depot if you have one locally. If you do not, it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]. Buy a pack of gloves while you're there too. Epoxy DOES NOT like to come off of skin.
 
The key thing here is to not use so much it will bleed over but also make sure you use enough to fill it in to the point that it doesn't fail as you only have one shot at this.
 
I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points.

현황:

open

원문 게시자: Nick ,

본문:

Depending on the extent of the damage, it may be possible to put them back in with a very small amount of Epoxy. However, this means the plastic MUST be intact. In many cases where this happens, the ABS plastic expanded and cracked just enough to fail. You can find this just about anywhere in retail to the point I'm just going to recommend going to Lowes or Home Depot if you have one locally. If you do not, it can be purchased on [https://www.amazon.com/Gorilla-Epoxy-85-oz-Clear/dp/B001Z3C3AG/|Amazon]

The key thing here is to not use so much it will bleed over but also make sure you use enough to fill it in to the point that it doesn't fail as you only have one shot at this.

I am going to assume you know how to take the laptop apart, since you have access to these broken anchor points. Once you have access, put a screw in a very, very small amount for grip (Epoxy is a bear to get off skin) and then spread it on the sides with a toothpick. Put them in and then immediately remove the screw. Do this with all of the failed anchor points.

현황:

open