주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

도움말

현재 버전 게시자: Nick ,

텍스트:

CRT monitors can hold up to ~15-25,000 volts (25,000 volts is usually reserved for TVs). '''''While this is the generally accepted rule, you should not assume this is going to be the case; treat the monitor as if it is holding the higher voltage at all times. Most modern CRT’s (90’s-final production) have a bleeder resistor, but this is often burned out and cannot be trusted. For this reason, you must discharge the CRT to be sure.'''''
 
Unless you know what you’re doing, you are better off leaving the repair to someone who knows what they are doing or replace it. These monitors hold enough charge to kill you if you screw up.
 
'''''If''''' '''''you still insist on trying, you need to take precautions. The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hand as the path of least resistance. DO NOT have both hands out at the same time, as this can create a killer circuit to your heart.'''''
 
'''''In addition to that, if you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up as it is an excellent conductor and electricity takes the path of least resistance.'''''
 
'''''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack or Fry's. These are not thick enough to handle the sustained CRT discharge load and will burn up. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.'''''
 
'''Before messing with''Before removing the boardanode, ALWAYS TOUCH THE LEADS WITH A SCREWDRIVER BEFORE REMOVING THE FLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.YOU.'''''
'''Before messing with''Before removing the boardanode, ALWAYS TOUCH THE LEADS WITH A SCREWDRIVER BEFORE REMOVING THE FLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.YOU.'''''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to ~15-25,000 volts (25,000 volts is usually reserved for TVs). '''While''While this is the generally accepted rule, you should not assume this is going to be the case; treat the monitor as if it is holding the higher voltage at all times.'''times. Most modern CRT’s (90’s and newer90’s-final production) have a bleeder resistor, but this is often burned out at this point due to years of stress. '''Forand cannot be trusted. For this reason, you must discharge the CRT as a safety precaution to be sure.sure.'''''
CRT monitors can hold up to ~15-25,000 volts (25,000 volts is usually reserved for TVs). '''While''While this is the generally accepted rule, you should not assume this is going to be the case; treat the monitor as if it is holding the higher voltage at all times.'''times. Most modern CRT’s (90’s and newer90’s-final production) have a bleeder resistor, but this is often burned out at this point due to years of stress. '''Forand cannot be trusted. For this reason, you must discharge the CRT as a safety precaution to be sure.sure.'''''
 
Unless you know what you’re doing, you are better off leaving the repair to someone who knows what they are doing or replace it. These monitors hold enough charge to kill you if you screw up.
 
If you'''''If''''' '''''you still insist on trying, you need to take precautions. '''TheThe best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hand as the path of least resistance. DO NOT have both hands out at the same time, as this can create a completekiller circuit that can kill you.to your heart.'''''
If you'''''If''''' '''''you still insist on trying, you need to take precautions. '''TheThe best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hand as the path of least resistance. DO NOT have both hands out at the same time, as this can create a completekiller circuit that can kill you.to your heart.'''''
 
'''If''In addition to that, if you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up, even if you take other precautions. Jewlrey provides little to no resistance.up as it is an excellent conductor and electricity takes the path of least resistance.'''''
'''If''In addition to that, if you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up, even if you take other precautions. Jewlrey provides little to no resistance.up as it is an excellent conductor and electricity takes the path of least resistance.'''''
 
'''If''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an exampleShack or Fry's. These are not thick enough to handle the sustained CRT discharge load discharging the CRT will put in the wire and will cause a fireburn up. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.overboard.'''''
'''If''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an exampleShack or Fry's. These are not thick enough to handle the sustained CRT discharge load discharging the CRT will put in the wire and will cause a fireburn up. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.overboard.'''''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS WITH A SCREWDRIVER BEFORE REMOVING THE FLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000~15-25,000 volts (Generally speaking, it’s ~15,00025,000 volts is usually reserved for aTVs). '''While this is the generally accepted rule, you should not assume this is going to be the case; treat the monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!)as if it is holding the higher voltage at all times.''' Most modern CRT’s (90’s and newer) have a bleeder resistor (usually from the 90’s going forward although some early monitors also have one)resistor, but this is often burnsburned out as they discharge the monitor over timeat this point due to highyears of stress. For'''For this reason, you must discharge the CRT as a safety precaution to be sure.sure.'''
CRT monitors can hold up to 15-25,000~15-25,000 volts (Generally speaking, it’s ~15,00025,000 volts is usually reserved for aTVs). '''While this is the generally accepted rule, you should not assume this is going to be the case; treat the monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!)as if it is holding the higher voltage at all times.''' Most modern CRT’s (90’s and newer) have a bleeder resistor (usually from the 90’s going forward although some early monitors also have one)resistor, but this is often burnsburned out as they discharge the monitor over timeat this point due to highyears of stress. For'''For this reason, you must discharge the CRT as a safety precaution to be sure.sure.'''
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it foryou are better off leaving the repair to someone who knows how to work on a CRT safelywhat they are doing or replace the monitorit. These monitors have the capacityhold enough charge to kill you if you get shockedscrew up.
Unless you know what you’re doing, I don’t recommend opening this. Leave it foryou are better off leaving the repair to someone who knows how to work on a CRT safelywhat they are doing or replace the monitorit. These monitors have the capacityhold enough charge to kill you if you get shockedscrew up.
 
HOWEVER, ifIf you still insist on trying to repair ittrying, you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offershand as the path of least resistance. DO NOT have both hands out at the same timetime, as this createscan create a complete circuit that can kill you.'''
HOWEVER, ifIf you still insist on trying to repair ittrying, you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offershand as the path of least resistance. DO NOT have both hands out at the same timetime, as this createscan create a complete circuit that can kill you.'''
 
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, evenup, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelryprecautions. Jewlrey provides little to no resistance.'''
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, evenup, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelryprecautions. Jewlrey provides little to no resistance.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS WITH A SCREWDRIVER BEFORE REMOVING THE FLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000 volts (Generally speaking, it’s ~15,000 volts for a monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistorresistor (usually from the 90’s going forward although some early monitors also have one), but this often burns out because ofas they discharge the stress it is undermonitor over time due to high stress. For this reason, you must discharge the CRT as a safety precautionprecaution to be sure.
CRT monitors can hold up to 15-25,000 volts (Generally speaking, it’s ~15,000 volts for a monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistorresistor (usually from the 90’s going forward although some early monitors also have one), but this often burns out because ofas they discharge the stress it is undermonitor over time due to high stress. For this reason, you must discharge the CRT as a safety precautionprecaution to be sure.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace itthe monitor. These monitors have the capacity to kill you if you get shocked.
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace itthe monitor. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelry provides little resistance.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS WITH A SCREWDRIVER BEFORE REMOVING THE FLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000 volts (Generally speaking, it’s ~15,000 volts for a monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelry provides little resistance.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 15-25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS INWITH A SCREWDRIVER BEFORE REMOVING THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGEDFLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.'''
'''Before messing with the board, ALWAYS TOUCH THE LEADS INWITH A SCREWDRIVER BEFORE REMOVING THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGEDFLYBACK ANODE to ensure it is discharged. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000 volts (Generally speaking, it’s ~15,000 volts for a monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelry provides little resistance.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,00015-25,000 volts you’re better off going overboard.'''
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,00015-25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS IN THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGED. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000 volts (Generally speaking, it’s ~15,000 volts for a monitor and ~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you wear any jewelry, it is imperative you take this off. This will become a hazard if you slip up and can be a way to kill you, even if you take the other precautions I mentioned below. Electricity takes the path of least resistance and jewelry provides little resistance.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS IN THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGED. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

CRT monitors can hold up to 15-25,000 volts (generallyGenerally speaking, it’s 15,000~15,000 volts for a monitor and 25,000~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
CRT monitors can hold up to 15-25,000 volts (generallyGenerally speaking, it’s 15,000~15,000 volts for a monitor and 25,000~25,000 volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS IN THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGED. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

These CRTCRT monitors can hold up to 15-25,000 volts (generally speaking, it’s 15,000 volts for a monitor and 25,000 volts.volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
These CRTCRT monitors can hold up to 15-25,000 volts (generally speaking, it’s 15,000 volts for a monitor and 25,000 volts.volts for televisions. However, DO NOT ASSUME THE VOLTAGE!) Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS IN THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGED. Again, failure to do this CAN KILL YOU.'''

현황:

open

편집자: Nick ,

텍스트:

These CRT monitors can hold up to 25,000 volts. Most modern CRT’s have a bleeder resistor, but this often burns out because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.
 
Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.
 
HOWEVER, if you still insist on trying to repair it you need to take precautions. '''The best advice I can give you that isn’t covered is to ALWAYS keep one hand behind your back - this will prevent a circuit from forming if the charge chooses your hands because it offers the least resistance. DO NOT have both hands out at the same time as this creates a complete circuit that can kill you.'''
 
'''If you do not know where to get a real discharge tool, it’s okay to use a rubber handled screwdriver with an alligator clip lead, but you do not want to use the ones from Radio Shack, just to name an example. These are not thick enough to handle the sustained load discharging the CRT will put in the wire and will cause a fire. Use car jumper wires if that’s all you have - it’s overkill but when you are dealing with 25,000 volts you’re better off going overboard.'''
 
'''Before messing with the board, ALWAYS TOUCH THE LEADS IN THE CRT BEFORE REMOVAL AFTER DISCHARGING IT TO ENSURE IT IS FULLY DISCHARGED. Again, failure to do this CAN KILL YOU.'''

현황:

open

원문 게시자: Nick ,

텍스트:

These CRT monitors can hold up to 25,000 volts. Most modern CRT’s have a bleeder resistor, but this often burns out  because of the stress it is under. For this reason, you must discharge the CRT as a safety precaution.

Unless you know what you’re doing, I don’t recommend opening this. Leave it for someone who knows how to work on a CRT safely or replace it. These monitors have the capacity to kill you if you get shocked.

현황:

open