주요 콘텐츠로 건너뛰기
도움말

현재 버전 게시자: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears any possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisable, one standing by to turn ofoff the main taps ;-)
Having two people to perform the test is advisable, one standing by to turn ofoff the main taps ;-)
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
Place a rag (or even a bucket upside down) over the tap fitting to prevent ''hot'' water going everywhere.
 
Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

편집 작업: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears any possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisableadvisable, one standing by to turn of the main taps ;-)
Having two people to perform the test is advisableadvisable, one standing by to turn of the main taps ;-)
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
Place a rag (or even a bucket upside down) over the tap fitting to prevent ''hot'' water going everywhere.
 
Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

편집 작업: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears any possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisable
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
OpenPlace a rag (or even a bucket upside down) over the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap fitting to increase the pressure flow through the hotprevent ''hot'' water service)going everywhere.
OpenPlace a rag (or even a bucket upside down) over the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap fitting to increase the pressure flow through the hotprevent ''hot'' water service)going everywhere.
 
Place a rag (or even a bucket upside down) overOpen the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap fitting to prevent ''hot''increase the pressure flow through the hot water going everywhere.service)
Place a rag (or even a bucket upside down) overOpen the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap fitting to prevent ''hot''increase the pressure flow through the hot water going everywhere.service)
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

편집 작업: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears any possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisable
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)
 
Place a rag (or even a bucket upside down) over the tap fitting to prevent ''hot'' water going everywhere.
Place a rag (or even a bucket upside down) over the tap fitting to prevent ''hot'' water going everywhere.
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

편집 작업: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears theany possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
Try the following and see if it clears theany possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisable
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)
 
Place a rag over the tap fitting to prevent ''hot'' water going everywhere.
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

편집 작업: jayeff ,

본문:

Hi @theends ,
 
Try the following and see if it clears the possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)
 
Having two people to perform the test is advisable
 
Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service) and the '''''main'' cold water tap''' to the house.
 
Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)
 
Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)
 
Place a rag over the tap fitting to prevent ''hot'' water going everywhere.
 
''Be careful as the water will be hot!''
 
Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open

원문 게시자: jayeff ,

본문:

Hi @theends ,

Try the following and see if it clears the possible obstruction in the pipe feeding the tap. (be prepared for water to come out under pressure)

Shutoff the '''''main'' hot water tap''' for the house (usually near the hot water service)  and the '''''main'' cold water tap''' to the house.

Remove the tap handle, spindle and washer from the bathroom sink’s hot water tap fitting (as if you’re going to replace the tap’s washer)

Open the main hot water tap and check the flow from the bathroom sink hot water tap fitting. (if there isn’t much pressure open the ''main'' cold water tap to increase the pressure flow through the hot water service)

Place a rag over the tap fitting to prevent ''hot'' water going everywhere.

''Be careful as the water will be hot!''

Once the hot water flows unobstructed, shut off the main hot water tap (and the main cold water tap if you’ve opened it) and replace the sink’s tap washer, spindle and handle etc.

현황:

open