My iPhone got briefly wet, no backlight?

Question

iPhone 3GS

처리 속도가 빨라진 iPhone 3G 개선 버전. 이 기기의 수리는 3G와 유사하며 간단한 스크루드라이버, 비집는 도구가 필요합니다. 모델 A1303 / 16GB 또는 32GB 용량 / 검정 또는 흰색 플라스틱 뒷면.

1500 질문 전체 보기

Austin Widner @austinwidner

평판: 1

1

게시일: 2012년 12월 8일

옵션

My iPhone got briefly wet, no backlight?

I went on a ladder going into the pool, and forgot about my iphone. However, I'd say it was submerged for literally 5 seconds because I got out right away. Now the backlight is completely gone. I opened it up, let it dry, soaked it in isopryol alcohol, and noticed that only 1 of the water damage indicators was tripped; the one in the headphone jack. The logic board has no signs of corrosion. However, the chip on the lcd did have some junk on it. What would I do for repairs? I don't want to waste time and money. Should I replace the LCD, 6r8 coil, or the voltage regulator? Also, I don't have much fine soldering skills. I wanna take the easiest and cheapest route to repair my phone.

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 -1

댓글 2개

EDIT: Yes it does power on. It was actually on when I went in and it was on when I came out... I've already completely disassembled it and soaked the logic board in the alcohol and gently scrubbed it with a tooth brush. My problem is the lcd backlight isn't on, but the screen is. Everything works besides the backlight. Also, I still use my phone, but it's a pain to see without the backlight.

Austin Widner 의 2012년 12월 9일

There I followed the guide... Same thing... I uploaded some pics to show what I am dealing with

Austin Widner 의 2012년 12월 9일

댓글 달기

답변 2개

선택된 답변

Mitch Rush @mitchrush

평판: 5.6k

6

3

4

게시일: 2012년 12월 9일

옵션

I wouldn't replace anything till you do a thorough water damage treatment to it, I rarely have to replace an LCD due to water damage or anything else for that matter, you didn't say if your phone powers up, or if you disassembled it, just that you soaked it, if I were you I would disassemble it, clean both sides of the motherboard and all ribbon cable connections with alcohol and a toothbrush with the heat shields removed, let it dry completely, if it wont power up after that try a new battery.If it was only under water a short time this should be easy bringing it back to life. Would love to here how you do, good luck. iPhone 3GS Teardown

해당 답변은 도움이 되었습니까?

예 아니요

점수 0

댓글 달기

EDIT: Yes it does power on. It was actually on when I went in and it was on when I came out... I've already completely disassembled it and soaked the logic board in the alcohol and gently scrubbed it with a tooth brush. My problem is the lcd backlight isn't on, but the screen is. Everything works besides the backlight. Also, I still use my phone, but it's a pain to see without the backlight. — Austin Widner
There I followed the guide... Same thing... I uploaded some pics to show what I am dealing with — Austin Widner

oldturkey03 @oldturkey03 평판: 781.7k 1.1k 893 2.3k · Answer 1 · 2012-12-09T10:35:10-07:00

oldturkey03 @oldturkey03

평판: 781.7k

1.1k

893

2.3k

게시일: 2012년 12월 9일

옵션

Austin Widner, I know you said you cleaned your phone, but just for completion sake, I suggest you clean it using this guide. It was written for a 3G but all the steps still pertain to your phone as well. Once cleaned, replace the battery and reevaluate. If you find that this does not have any impact on your problems, there are two way you can go. One is to replace the LCD, since this is where the actual backlight is situated, the other one is to replace the 6R8 coil. Part of this now depends on your comfort level. The coil is cheaper to replace, but will require some very fine soldering on the logic board. The LCD is easier to replace. Here is a decent video to show the procedure, and the coil is available at multiple places, i.e. Digikey.com part number is 445-3226-1-ND Hope this helps, good luck.

해당 답변은 도움이 되었습니까?

예 아니요

점수 0

댓글 달기

iPhone 3GS

My iPhone got briefly wet, no backlight?

답변 2개

귀하의 답변을 추가하세요