Multimeter Question- Battery and Charging fuse

Question

iPhone 3GS

처리 속도가 빨라진 iPhone 3G 개선 버전. 이 기기의 수리는 3G와 유사하며 간단한 스크루드라이버, 비집는 도구가 필요합니다. 모델 A1303 / 16GB 또는 32GB 용량 / 검정 또는 흰색 플라스틱 뒷면.

1500 질문 전체 보기

질문 마감됨

Danny Puggsy @dannypuggsy

평판: 1

1

게시일: 2013년 2월 6일

옵션

Multimeter Question- Battery and Charging fuse

Hi,

I done a multimeter test on my iphone 3gs battery and charging fuse but i dont know if im doing it right. The board is disconnected from the phone (so no power) and when i place the multimeter (9v) on the board it is readin 0.3Ω on the charging fuse and 0.2Ω on the battery fuse. Is this correct or should it be showing something different? I cant seem to get the phone to switch on and i have done a battery change, tried different chargers and leads. I put the motherboard in my working 3GS and nothing happened so it suggests to me that theres a motherboard problem. Can anyone help me please?

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 1개

Not an answer. My phone won't charge B/4 or after battery replacement. Did you resolve your problem? If so, how?

irishmikeh 의 2013년 5월 19일

댓글 달기

답변 1개

선택된 답변

oldturkey03 @oldturkey03

평판: 782.2k

1.1k

893

2.3k

게시일: 2013년 2월 6일

옵션

Danny Puggsy, I wouldn't worry to much about the resistance at this point. The "fuses" are not really fuses. the one referred to as battery fuse is actually a 0.050 1% 1/3W MF 805 resistor and the "charging fuses" are FERR-120-OHM-1.5A inductors. So measuring it in resistance could give you erroneous results. Check for continuity will give you a better idea. Hope this helps, good luck.

Battery "Fuse"

Charging "Fuse"

해당 답변은 도움이 되었습니까?

예 아니요

점수 4

댓글 12개:

Hi Oldturkey, Thanks for your reply it is most appreciated. so what setting should my multimeter be on in order to measure the continuity? Sorry to sound like an amateur but i havent really used one of these before on a motherboard, i have a fluke 77IV (cant seem to upload a photo). I'm assuming the motherboard is the issue as i have put it in my working 3gs and the phone doesnt power up. Thanks

Danny Puggsy 의 2013년 2월 7일

Nice meter :-) Anyhow, set your multimeter to the correct mode. Look for the icon that looks like a sound wave, on your meter it is at the 2o'clock position.Touch one of the probes off one of the points of the "fuse", touch the other probe off the other point. If you hear a beep or a buzz, there is an electric connection between the two points, which means it has continuity, if there is no connection you will not hear a beep or a buzz and the display will give a reading of 0.

oldturkey03 의 2013년 2월 7일

Forgot to ask if you have done a hard reset when you changed the board. Have you tried a different dock connector? It could shorten out the circuit if faulty.

oldturkey03 의 2013년 2월 7일

For some of the voltages on your logic board, check my answer on this question How to replace the power IC, iPhone 3GS logic board?

oldturkey03 의 2013년 2월 7일

Thank you for the advice :). I will check these when i get home, i havent chnaged the dock connector yet but i have got one there ready to go so i shall try it, thanks. No i didnt do a hard reset when i put the motherboard in my phone as there was no power, which is why im suspecting a motherboard issue, is it worth soaking the board in isopropyl alcohol just incase there is any corrosion?

Danny Puggsy 의 2013년 2월 8일

댓글 7개 더보기

댓글 달기

Not an answer. My phone won't charge B/4 or after battery replacement. Did you resolve your problem? If so, how? — irishmikeh
Hi Oldturkey, Thanks for your reply it is most appreciated. so what setting should my multimeter be on in order to measure the continuity? Sorry to sound like an amateur but i havent really used one of these before on a motherboard, i have a fluke 77IV (cant seem to upload a photo). I'm assuming the motherboard is the issue as i have put it in my working 3gs and the phone doesnt power up. Thanks — Danny Puggsy
Nice meter :-) Anyhow, set your multimeter to the correct mode. Look for the icon that looks like a sound wave, on your meter it is at the 2o'clock position.Touch one of the probes off one of the points of the "fuse", touch the other probe off the other point. If you hear a beep or a buzz, there is an electric connection between the two points, which means it has continuity, if there is no connection you will not hear a beep or a buzz and the display will give a reading of 0. — oldturkey03
Forgot to ask if you have done a hard reset when you changed the board. Have you tried a different dock connector? It could shorten out the circuit if faulty. — oldturkey03
For some of the voltages on your logic board, check my answer on this question How to replace the power IC, iPhone 3GS logic board? — oldturkey03
Thank you for the advice :). I will check these when i get home, i havent chnaged the dock connector yet but i have got one there ready to go so i shall try it, thanks. No i didnt do a hard reset when i put the motherboard in my phone as there was no power, which is why im suspecting a motherboard issue, is it worth soaking the board in isopropyl alcohol just incase there is any corrosion? — Danny Puggsy