메인 컨텐츠로 가기

Apple iPhone 5s는 2013년 9월 10일에 발표되었습니다. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 16, 32, 또는 64GB / 은색, 금색 및 스페이스 그레이.

3947 질문 전체 보기

Battery adhesive removal failure

I have tried to use ifixit guide to replace battery in my iPhone 5s.

When I got to steps to remove adhesive tape, unfortunately the tape tabs just went off (just tore off) without removing adhesive from underneath the battery.

These are steps 21-25 here: How to replace the battery in your iPhone 5s

How can I still remove the old battery?

해당 질문 답변하기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 10
코멘트 추가

안드로이드 수리 키트

새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

지금 장보기

안드로이드 수리 키트

새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

지금 장보기

4개의 답변

가장 유용한 답변

Heat up the rear of the iPhone were the battery is situated the aluminum part..

Now pry the battery up with a metal pry tool only pry on the volume keys side not on the motherboard side..

Pry in the middle and bottom side of battery as there is flex cables under the battery at the top of it.. The battery will bend as the adesive is really tuff but saying as your changing the Battery this doesn't matter

이 답글이 도움이 되었나요?

점수 4

댓글:

Ir worked! Thank you.

의 답변

코멘트 추가

when the adhesive strips are broken , you can try using fishing line to remove the adhesive from under the battery - https://www.youtube.com/watch?v=gkCyl7kR...

also this method using steel wire seems even better - https://www.youtube.com/watch?v=W5GzU11q...

이 답글이 도움이 되었나요?

점수 1
코멘트 추가

Don't heat up adhesive tabs used to hold down batteries of iPhone 5s, 6 Etc. These are command strips from 3m and become brittle when heated. If you break them off gently pry up on battery using plastic pry tool or isesamo. Be extremely careful not to puncture battery. I get the battery up enough to use curved tweezers and grab a hold of that command strip and pull directly away from itself.

이 답글이 도움이 되었나요?

점수 0
코멘트 추가

I did two battery replacements back to back, and on the second I used the black spudger as a spool, basically: # NOT cutting the tabs in 2

  1. laying the spudger across the frame with the edge over the battery's bottom edge and pulling the tabs over it
  2. Slowly rolling the spudger towards the home button, keeping the angle of tape more or less vertical from the battery's edge.

On side of the tape broke early on because i misunderstood ifixit's directions and was pulling the tape forward at an angle over the home button hardware. I can't say for certain this method would work consistently but I was surprised how well it did- certainly better than pulling and re-gripping separate tabs.

이 답글이 도움이 되었나요?

점수 0
코멘트 추가

답변 추가

andrewborodenko 이(가) 영원히 고마워 할 것입니다.
View Statistics:

Past 24 Hours: 30

Past 7 Days: 134

Past 30 Days: 608

All Time: 21,133