주요 콘텐츠로 건너뛰기

2012년 9월 12일에 발표된 여섯 번째 Apple iPhone입니다. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 16, 32, 또는 64GB / 검정색 또는 흰색으로 제공하였습니다.

2521 질문 전체 보기

Battery and charge port changed, still won't charge?

A couple of weeks ago my phone ran out of battery and wouldn't take a charge. I noticed the charge cable wasn't sitting in the port too well so narrowed it down to a worn out charge port, ordered a new one, fitted fine, still no power.

I then figured it must be the battery so ordered a new one. Fitted fine, powered on once phone was connected to a charger (battery came with approx 75% charge) however, the battery won't charge further than this. I changed the charge port back over to the original and the same happens. Turns on once connected but will not charger, it must be connected properly as it is powers on when plugged in.

I've gone through and checked everything is attached properly.

Any ideas?

Thank you for your time and any help you may be able to offer.

이 질문에 답하기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 6
댓글 달기

답변 5개

가장 유용한 답변

If you have had both of those parts replaced and have tried a known working Apple original charger and charge cable, then this is very likely your problem:

http://www.macrumors.com/2014/06/19/ipho...

해당 답변은 도움이 되었습니까?

점수 1

댓글 4개:

Ah that seems about right. Thanks. Any idea on repairs/parts?

There are definitely folks out there that will repair this issue. I don't personally have the skills to do motherboard repair, and unfortunately don't have anyone to recommend to you either, but I'm sure some Google searching will turn up something for you. Or, perhaps someone else can chime in with a suggestion.

No worries guys. Thanks for your help. Ive had a good read up on it and may know someone who can give it ago. Thanks again. Much appreciated.

Pls were u able to solve t, av d xam issue

댓글 달기

The iphone wont charge because of an issue with the U2 IC chip on the motherboard. To repair this, you need a professional to either reball the chip or replace it (Replacing is always better).

This is why your iphone will not sync or charge even when the battery and charging ports are replaced. This is a very common issue. If you have never soldered micro chips before, I suggest you find someone that can.

해당 답변은 도움이 되었습니까?

점수 1
댓글 달기

i have some problem once on iphone 4,i change and replaced charge port and battery double time.but i wont charged. when i recheck,charge port and battey cord is correct voltage on digital meter, Then i change the "usb cable" and "charger adaptor" it was fixed.

해당 답변은 도움이 되었습니까?

점수 0

댓글 1개:

Stupidly I only tried one cable but its one that I use on my iPad so I know it works. Worth trying another cable.

댓글 달기

Maybe a long shot, but have you checked for any bent pins where the charging port plugs into? Or any corrosion/lint/dirt on the usb cable which plugs into the charge port?

해당 답변은 도움이 되었습니까?

점수 0

댓글 1개:

Well as its a brand new charge port it wouldn't have any dirt build up. My old one does look mega worn but the new one looked fine. Just finding it weird that it recognises the port is plugged in to turn the phone on in the first place. Just nothing else after that.

댓글 달기

U2 IC is probably damaged. Don't try to replace it if you don't have the skills and equipment.

해당 답변은 도움이 되었습니까?

점수 0

댓글 1개:

Don't try to replace it unless you "don't" have the skills ??

At any rate you will need a monoscope. A microscope attached to a monitor. You will also need a micro soldering station. They are expensive. You can't do it at home.

댓글 달기

귀하의 답변을 추가하세요

ben 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 6

30일 전: 19

전체 시간: 35,972