Released on September 19, 2014, this 4.7" screen iPhone is the smaller version of the iPhone 6 Plus. Identifiable by the model numbers A1549, A1586, and A1589.

4419 질문 전체 보기

Circuit board water damage repair

I have a iPhone 6 that has water damage on the circuit board. I have looked over the entire board and cannot find any other corrosion issues. Should I try to clean it with isopro. Alcohol or bring it in for a board level repair?

Block Image

. Can someone help with identification of this part and a cost to replace it? Thanks

답변되었습니다! View the answer 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 3
의견 추가하세요
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12

3개의 답변

선택된 해법

@cajunphone if you looked over the board you obviously will have to remove all the EMI shileds. You got at least 60% of your boards components covered with those. You cannot do a proper "inspection" without removing those.

I suggest you treat this just like any other water damaged iPhone. The very first thing you want to do is to clean it. Disassemble your phone using this guide. You must remove all EMI shields. If you do not remove those, you might as well not do anything. After you removed those, clean the whole board, connectors and all with +90% isopropyl alcohol. Just soaking it will not help. Follow this guide , and even so it was written for a 3G all the points are still pertinent to your phone. While you clean your board, check for any obvious damage, like burned or missing components etc. When it is properly cleaned, replace the battery. All these steps are to avoid delayed failure caused by corrosion. Best thing to do would be to clean it with an ultrasonic cleaner, but if you do not have access to one, this will at least help. Once all this is done, reassemble your phone, replace your batteryand reevaluate. Until it is cleaned, everything will only be a guess. Even with all this, water damage has only a small chance to be fully repaired, but at least you can give it a try.

The component you are looking at (large IC) is the Murata 339S0228 Wi-Fi Module

iPhone 이미지

안내서

Repairing iPhone Liquid Damage

난이도:

어려움

1 - 2 hours

iPhone 6 Logic Board 이미지

안내서

iPhone 6 Logic Board Replacement

난이도:

보통

30 minutes - 2 hours

해당 답변은 도움이 되었습니까?

점수 2
의견 추가하세요

The component with the most damage is the capacitor that is burnt there. It goes from vcc main to ground. If it is shorted, which is very likely judging by the looks of it, you will have no power to the rest of the phone. I would test it for a short and remove it (WITH a soldering iron) and test for a short to ground again. If it is not shorted anymore, start the phone making sure nothing gets to hot to touch. The chip there is the wifi/ bluetooth chip. If you knock any of the other components off the board though, you may lose wifi and/or bluetooth. Definitely clean and dry the board too.

해당 답변은 도움이 되었습니까?

점수 2
의견 추가하세요

You should definitely clean it with isopropyl alcohol first. Then move on to the harder solutions. I believe that's the power management ic

해당 답변은 도움이 되었습니까?

점수 1

댓글:

Literally you just posted that 10 seconds before me and I was just going to say the same thing lol

의 답변

Haha. Great minds think alike

의 답변

Great minds? To Funny LOL ;-))

의 답변

Thanks old turkey and imedic and will update on my progress

의 답변

Not very nice, old turkey

의 답변

1에 댓글 더 나타내기

의견 추가하세요

귀하의 답변을 추가하십시오

Joe Bab 가/이 대단히 고마워 할 것입니다.
조회 통계:

지난 24시간: 13

지난 7일: 63

지난 30일: 276

전체 시간: 13,764