Why does my 2.5GHZ Quad freeze shortly after booting?

Question

Power Mac G5

PowerMac G5는 Apple Corporation에서 2003년에 처음 제조한 데스크톱 컴퓨터입니다. 이 안내서는 2004년 Apple PowerMac G5 모델 번호 A1047 EMC 2061의 수리 과정을 검토합니다. 2006년에 먼저 개발자에게 그 후 소비자에게 Intel 스위치의 일환으로 판매가 중단되었습니다.

197 질문 전체 보기

Brian @brian13349

평판: 23

2

게시일: 2011년 1월 13일

옵션

Why does my 2.5GHZ Quad freeze shortly after booting?

Note that this Power Mac G5 (late 2005) freezes before I can boot into the Apple System Diagnostic or immediately after booting into OS 10.4.11. First LED #2 lights up, and then LED #7 lights up and the unit freezes. Video is fine. I have tried a different video card, and different memory with no luck. I have reset the SMU, and I have vacuumed/blown out the inside of the unit thoroughly. Everything appears to be functioning properly, including the Superdrive.

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 달기

답변 2개

선택된 답변

mayer @mayer

평판: 685.3k

MacHale Enterprises

3.4k

1.1k

2.6k

게시일: 2011년 1월 13일

옵션

The #2 indicates no memory

The #7 should flash once at startup, then go off. If it stays on,

it indicates a CPU hang. This is usually caused by bad RAM, but

the CPU assembly may have come loose, or there may be a problem

with the connector for it (or it could have just plain died).

Cut back to the original RAM configuration and see if that fixes it (minimal RAM)

On all versions of the Power Mac G5, you must install memory in pairs. There is a top bank of sockets and a lower bank. When you install a ram module in the top bank, you must install the exact same size memory chip in the corresponding socket of the lower bank.

해당 답변은 도움이 되었습니까?

예 아니요

점수 3

댓글 3개:

To explain a little more, the unit starts up normally. After 30 seconds or so LED #2 comes on, and stays on, but the unit continues to function normally. After another 20 seconds or so LED #3 comes on too and the unit freezes. Different memory has been tried, and I forgot to mention that the battery was replaced.

Brian 의 2011년 1월 13일

I guess I'm going to have to figure this one out myself...I guess I'm going to have to figure this one out myself...

Brian 의 2011년 1월 19일

Okay, I've replaced RAM, the video card, the mother board and the CPU's. It starts up properly, all the fans work and I still get the same 2 LEDs lighting up with the system freezing. I know a lot of tricks, but I retired as a Field Engineer just before any of the G5s were released, so I need some help from someone with some serious experience with the things, if you please...

Brian 의 2011년 1월 20일

댓글 달기

To explain a little more, the unit starts up normally. After 30 seconds or so LED #2 comes on, and stays on, but the unit continues to function normally. After another 20 seconds or so LED #3 comes on too and the unit freezes. Different memory has been tried, and I forgot to mention that the battery was replaced. — Brian
I guess I'm going to have to figure this one out myself...I guess I'm going to have to figure this one out myself... — Brian
Okay, I've replaced RAM, the video card, the mother board and the CPU's. It starts up properly, all the fans work and I still get the same 2 LEDs lighting up with the system freezing. I know a lot of tricks, but I retired as a Field Engineer just before any of the G5s were released, so I need some help from someone with some serious experience with the things, if you please... — Brian