기기를 수리하세요 커뮤니티 상점

2012년 9월 12일에 발표된 여섯 번째 Apple iPhone입니다. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 16, 32, 또는 64GB / 검정색 또는 흰색으로 제공하였습니다.

2522 질문 전체 보기

옵션

Missing resistor for home button iPhone 5

Hi,

I had to check the motherboard of my Iphone 5 after home button problemes

The BGA U3 resistor is there but i noticed one resistor close a connector(i don't know how it called ) is missing.

As you can see on the pic , one in the middle of the 3 resistors vanished.

Where can i get a free schematics for an iPhone 5, so i can get the correct resistor value ?

Which are the other possible ways to get the probleme fixed ?

Home button actually works with some pencil's graphite but Iphone can't be shaked and has obviously to be steady.

Can a soldering dot fix it temporary ? Where to buy this component ?

Sorry for my poor english and thanks in advance for help.

Block Image

Block Image

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요
점수 0
댓글 달기

답변 3개

필터:
가장 유용함 가장 최근 가장 오래된
선택된 답변

옵션

The missing component is a ferrite bead (FL5). It's specs are 120Ohms / 210mA / 01005. You can find them at Digikey.com under the following part number (445-8668-1-ND). It's the same component as the backlight filter.

해당 답변은 도움이 되었습니까?

예 아니요
점수 3

댓글 3개:

Thank you , amazed with this fast professional reply. Unfortunately i have to find another solution because cost shipping are too high for France. Thanks again for this reference , it was so difficult to find .

의

If a micro jumper is okay , is it possible to solder any resistor since the size is same as the missing one and no matter the value ? Thanks advance for answer

Thanks in advance .

의

No, you shouldn't put a resistor in place of a ferrite bead. They have different functions. A micro-jumper is okay for testing purposes.

의

댓글 달기

옵션

yes this is possible to repair, you can either get a resistor from a donor board, and solder it on using a hot air work station or fine soldering tweezers, alternatively as it is a resistor you can just use a small jumper wire method. We repair these all the time, it is easy if you are experienced in micro soldering. Hope this helps.

해당 답변은 도움이 되었습니까?

예 아니요
점수 1

댓글 2개:

Thank you very much.

Can i ask what is a "small jumper wire method" ?

I am not a big experienced in soldering but in think i can make a "dot", a "jumper wire" sounds different .

I was thinking that if a dot of graphite can make miracle, a solder dot can too. Thanks

의

i dont think a solder dot will be a good idea, you want to make a micro jumper between the two points, if you are unable to perform such a task, i dont mind doing it for you, i specialise in micro soldering

의

댓글 달기

옵션

If a micro jumper is okay , is it possible to solder any resistor since the size is same as the missing one and no matter the value ? ( here a 01005 resistor)

Thanks in advance .

해당 답변은 도움이 되었습니까?

예 아니요
점수 0
댓글 달기

귀하의 답변을 추가하세요

Marfr 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 248