Touch is not working. Missing a voltage?

Question

iPhone 6

2014년 9월 19일에 출시된 이 4.7” 스크린 iPhone은 iPhone 6 Plus의 작은 버전입니다. 모델 번호 A1549, A1586 및 A1589로 식별됩니다.

4994 질문 전체 보기

Joseph Hughes @joesipaq

평판: 795

La Clínica de la Manzana

8

6

1

게시일: 2018년 4월 28일

옵션

Touch is not working. Missing a voltage?

Hello all,

More of a technical question... I have an iPhone 6 with no touch. Before lifting cumulus I was poking around for voltages and am missing PP5V1_GRAPE_VDDH. There is no short to ground on that line.

I pulled U1501 and replaced it with one I had on a doaner board that might have been bad. I lost all image on the screen but had backlight after that.

Retracing my steps, I reballed the original U1501 an stuck it back on and the phone is back to how it was.

Should I order and install a new U1501 or is there something else you would advise me to check first?

Thanks all and happy repairing!

Joseph

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 달기

답변 1개

선택된 답변

daniel @tech_ni

평판: 34.6k

10

22

44

게시일: 2018년 4월 28일

옵션

did you try meson to see if it could be an issue

해당 답변은 도움이 되었습니까?

예 아니요

점수 2

댓글 28개:

Honestly no I have not. Before pulling it off I thought I would check voltages going to the two.

If it were an ip6+ they for sure first thing would be an M1 jumper. But in this case, no stress on the board seems to make any difference in it working, so I was leaning away from classic touch diseases (also being a 6 not a 6 plus) are there some inputs I should test out for menson? Or what would you recommend I do to it?

Joseph Hughes 의 2018년 4월 28일

cumulus and meson have connected lines like CUMULUS_TO_MESON_VSTM_OUT_N, CUMULUS_TO_MESON_VSTM_OUT_P, CUMULUS_TO_SAGE_BOOST_CLK_EN, TOUCH_I2C_SCL, TOUCH_I2C_SDA

daniel 의 2018년 4월 28일

also did you check resistance on j2401

daniel 의 2018년 4월 28일

I didn't check resistances on j2401, somehow that passed my mind .... Surprised. That could easily tell me what it might be.

Is it normal for U1501 to have 2 of the 3 power outputs OK and the third dead? That's my primary thought on this one at the moment. I don't have the schematics here with me at home, butbinkimda thought that they would all be present, or none.

Joseph Hughes 의 2018년 4월 28일

I will definitely check those lines though on Monday

Joseph Hughes 의 2018년 4월 28일

댓글 23개 더보기

댓글 달기

Honestly no I have not. Before pulling it off I thought I would check voltages going to the two.

If it were an ip6+ they for sure first thing would be an M1 jumper. But in this case, no stress on the board seems to make any difference in it working, so I was leaning away from classic touch diseases (also being a 6 not a 6 plus) are there some inputs I should test out for menson? Or what would you recommend I do to it? — Joseph Hughes
cumulus and meson have connected lines like CUMULUS_TO_MESON_VSTM_OUT_N, CUMULUS_TO_MESON_VSTM_OUT_P, CUMULUS_TO_SAGE_BOOST_CLK_EN, TOUCH_I2C_SCL, TOUCH_I2C_SDA — daniel
I didn't check resistances on j2401, somehow that passed my mind .... Surprised. That could easily tell me what it might be.

Is it normal for U1501 to have 2 of the 3 power outputs OK and the third dead? That's my primary thought on this one at the moment. I don't have the schematics here with me at home, butbinkimda thought that they would all be present, or none. — Joseph Hughes

iPhone 6

Touch is not working. Missing a voltage?

답변 1개

귀하의 답변을 추가하세요