Is it possible to test iPhone 8 LCD prior to install?

Question

iPhone 8

2017년 9월 22일 출시. Model A1863, A1905. GSM 또는 CDMA / 64 또는 256 GB / 금색, 은색 및 스페이스 그레이.

872 질문 전체 보기

Supleh2 @supleh2

평판: 547

7

8

1

게시일: 2018년 7월 23일

옵션

Is it possible to test iPhone 8 LCD prior to install?

I'm in the process of replacing the LCD on an iPhone 8. In the past (on older models), I've always tested the LCD prior to transferring all of the LCD assembly components. However, when I connect the LCD ribbon cables and power up the phone it only displays the Apple logo. If I disconnect the battery and reattach the LCD cables of the OEM screen the phone boots up. What components of the old LCD assembly HAVE to be attached to the new one to test it prior to a full install? Could it be the home button assembly not being installed or something not being grounded or any essential screws?

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 1개

Thanks Ben. Got my triwing bits in and connecting the home button did the trick. Booted up like a charm.

Supleh2 의 2018년 7월 30일

댓글 달기

답변 1개

선택된 답변

Ben @benjamen50

평판: 159.7k

Mtwo Perform

11

191

368

게시일: 2018년 7월 24일

옵션

You are right, you need at least a home button plugged to LCD for phone to boot up normally.

If this is going to be your first screen replacement on a 8 phone, please be careful of the front camera assembly especially where the proximity sensor and ambient light sensor is.

Their next to each other and are held in snug with plastic gasket (one piece to hold both) and a bit of glue. I recommend heating them up well (80°C for like 5-10 seconds) to weaken / loosen the glue and adhesive.

해당 답변은 도움이 되었습니까?

예 아니요

점수 6

댓글 3개:

Thanks. After posting this as I was performing additional research. I came across information indicating the screen issue could be the result of the iOS version as well, is that true? Thanks for the additional info regarding the front camera assembly/housing.

Supleh2 의 2018년 7월 24일

What do you mean by screen issue?

Are you referring it being stuck on apple logo or the ambient light sensor where auto brightness does not work after screen replacement or something else?

Ben 의 2018년 7월 25일

Indeed without the home button, it may take a very long time to boot. I would normally remove the home button and front cam from the broken screen. Then attach the front cam directly to the mother board, and the home button to the new screen, power on, and test. If all ok, I would assembly properly.

Rany 의 2018년 7월 25일

댓글 달기

Thanks Ben. Got my triwing bits in and connecting the home button did the trick. Booted up like a charm. — Supleh2
Thanks. After posting this as I was performing additional research. I came across information indicating the screen issue could be the result of the iOS version as well, is that true? Thanks for the additional info regarding the front camera assembly/housing. — Supleh2
What do you mean by screen issue?

Are you referring it being stuck on apple logo or the ambient light sensor where auto brightness does not work after screen replacement or something else? — Ben
Indeed without the home button, it may take a very long time to boot. I would normally remove the home button and front cam from the broken screen. Then attach the front cam directly to the mother board, and the home button to the new screen, power on, and test. If all ok, I would assembly properly. — Rany

iPhone 8

Is it possible to test iPhone 8 LCD prior to install?

답변 1개

귀하의 답변을 추가하세요