기기를 수리하세요 커뮤니티 상점

1997-2003 Chevrolet Malibu Tail Lights Replacement

소개

Replacing burnt out or broken bulbs is a quick and easy fix that makes your car easier to see from behind, helping to prevent accidents.

필요한 것

  1. 1997-2003 Chevrolet Malibu Tail Lights Replacement, Tail Lights: 1 단계, 이미지 1/1

    • Locate the plastic casing that holds the trunk liner in place, directly behind the tail light.

    • Unscrew the plastic casings.

    번역하기

  2. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 2 단계, 이미지 1/1

    • Make sure to put some pressure on the tail light itself so it does not fall out when you unscrew it.

    • Unscrew the three plastic wing nuts located behind the tail lights.

    번역하기

  3. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 3 단계, 이미지 1/1

    • When the tail light assembly comes loose, do not fully remove it because it may damage the connected wires.

    • Carefully pull the tail light away from the car to expose the connected wires.

    번역하기

  5. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 4 단계, 이미지 1/3 1997-2003 Chevrolet Malibu Tail Lights Replacement: 4 단계, 이미지 2/3 1997-2003 Chevrolet Malibu Tail Lights Replacement: 4 단계, 이미지 3/3

    • Unclip the rear panel of the tail light assembly. There are two clips on the top and two on the bottom.

    • Remove the rear panel from the rest of the assembly.

    번역하기

  6. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 5 단계, 이미지 1/1

    • Do not pull on the bulb, handle it gently because it is fragile.

    • Grab the plastic base of the bulb and gently wiggle it free.

    번역하기

  7. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 6 단계, 이미지 1/1

    • When handling the new bulbs, avoid touching the glass as much as possible because this can reduce the life of the bulb.

    • Gently push the new bulb into the plastic housing.

    번역하기

  8. 1997-2003 Chevrolet Malibu Tail Lights Replacement: 7 단계, 이미지 1/1

    • After putting the new bulbs in, turn the desired lights on to check that the newly installed bulbs work correctly.

    • These bulbs have different functions including blinkers, brake lights, hazard lights, and back-up lights. They will only turn on when the necessary signal is sent.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 4명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Sank Yang

회원 가입일: 10/03/12

484 평판

안내서 5개 작성하였습니다

배지: 11

배지 +8개 더

팀

Cal Poly, Team 9-15, Amido Fall 2012 Cal Poly, Team 9-15, Amido Fall 2012 회원

CPSU-AMIDO-F12S9G15

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 10

30일 전: 37

전체 시간: 19,377