기기를 수리하세요 커뮤니티 상점

2006-2013 Toyota Corolla Ignition Coil Replacement

소개

This is a guide to remove an old ignition coil and install a new one. This is standard maintenance for this vehicle and can be preformed with just a socket wrench with a ten millimeter head.

필요한 것

  1. 2006-2013 Toyota Corolla Ignition Coil Replacement, Ignition Coil: 1 단계, 이미지 1/3 2006-2013 Toyota Corolla Ignition Coil Replacement, Ignition Coil: 1 단계, 이미지 2/3 2006-2013 Toyota Corolla Ignition Coil Replacement, Ignition Coil: 1 단계, 이미지 3/3

    • Pop the hood and remove the black plastic cover over the engine.

    • There is nothing to unscrew, or unlatch, and the cover should lift off. Once removed, the top of the engine will look like the third picture

    번역하기

  2. 2006-2013 Toyota Corolla Ignition Coil Replacement: 2 단계, 이미지 1/2 2006-2013 Toyota Corolla Ignition Coil Replacement: 2 단계, 이미지 2/2

    • Unplug the ignition coil you wish to replace. The coils are numbered one though four, left to right.

    • Do not unscrew the bolt on the ignition coil before this step. It makes the electrical plug more difficult to remove

    번역하기

  4. 2006-2013 Toyota Corolla Ignition Coil Replacement: 3 단계, 이미지 1/1

    • Unscrew the bolt of the coil that needs to be replaced.

    • Be sure to put the bolt in a place you will not lose it!

    번역하기

  5. 2006-2013 Toyota Corolla Ignition Coil Replacement: 4 단계, 이미지 1/2 2006-2013 Toyota Corolla Ignition Coil Replacement: 4 단계, 이미지 2/2

    • Pull the coil straight up and out. It should come off of the spark plug with little resistance.

    번역하기

  6. 2006-2013 Toyota Corolla Ignition Coil Replacement: 5 단계, 이미지 1/2 2006-2013 Toyota Corolla Ignition Coil Replacement: 5 단계, 이미지 2/2

    • Apply a pea-sized amount of grease to the new ignition coil. It should be all around the rubber tip around the bottom.

    • While not required, this step will make any future replacements much easier.

    번역하기

  7. 2006-2013 Toyota Corolla Ignition Coil Replacement: 6 단계, 이미지 1/1

    • When inserting the new ignition coil, press down lightly to ensure it is completely in place.

    • Re-plugging in the ignition coil, and re-screw it in. This can be preformed in either order.

    • Repeat steps three through five as necessary for the other three ignition coils.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Henderson Gillette

회원 가입일: 09/23/23

160 평판

안내서 1개 작성함

배지: 5

배지 +2개 더

팀

Austin Community College, Team 22-3, Watkins Fall 2023 Austin Community College, Team 22-3, Watkins Fall 2023 회원

AUSTINCC-WATKINS-F23S22G3

2 회원들

안내서 2개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 7

7일 전: 69

30일 전: 315

전체 시간: 1,045