이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.
필요한 것
-
-
Ensure car jack is ready by rotating handle clockwise completely
-
Locate metal beam under car used for jacking
-
Position car jack platform under metal beam
-
-
-
Pump car jack handle to raise up car
-
Raise up car stand 4 notches
-
Place car stand underneath wheel metal beam
-
-
-
Lower car onto the stands by rotating the jack handle counter-clockwise (very gently)
-
Repeat steps 1-3 on driver side of car
-
At this point, both sides should be raised off the ground
-
Place clean cardboard underneath the car
-
-
-
Locate the oil container underneath the car (this will require crawling under the car and laying on your back
-
Locate the bolt used to drain the oil
-
Position the oil drip pan underneath the bolt
-
-
-
Loosen the bolt by turning the 5/16 allen wrench counter-clockwise
-
Once loose, remove the bolt by hand
-
Wait ~10 minutes for all the oil to drain out
-
-
-
Clean up the drainage hole with paper towel
-
Insert the bolt, turning clockwise
-
Tighten the bolt with the 5/16 allen wrench until the wrench won't turn any further. This is plenty tight.
-
-
-
Position drip pan underneath the plastic cover as shown in picture
-
Open the hood of the car
-
Locate the oil filter
-
-
-
-
Get new oil filter
-
Install oil filter
-
Turn the oil filter counter clockwise to install (as appears to the user)
-
Tighten by hand until both hands can't get it any tighter - This is plenty tight
-
-
-
Wipe up the oil that spilled out when you replaced the filter
-
-
-
Locate the oil cap
-
Remove the oil cap
-
Place funnel into oil cavity
-
-
-
Remove oil dipstick
-
Clean oil dipstick with paper towel
-
Insert oil dipstick all the way
-
Remove oil dipstick
-
-
-
Check Oil Level
-
If oil is too low, add more
-
Oil is full when the level is just below the bend in the metal of the dipstick
-
-
-
Empty any remaining oil in the filter into the oil drip pan
-
Turn the oil filter upside down and place into the box of the filter that was just installed into the car
-
Mark the filter box as "old"
-
Return the filter to a mechanic shop for recycling
-
-
-
Prepare car jack by turning the handle clockwise all the way
-
Pump the car jack and position the jack underneath the metal beam
-
Continue pumping the jack, raising the car off the car stands
-
Remove the car stand
-
-
-
Lower the individual car side onto the ground by turning the handle of the car jack counter-clockwise
-
Repeat step 18 and 19 for the other side of the car
-
-
-
Turn on car
-
Leave car running for 5 minutes to let oil circulate
-
After 5 minutes, check oil level using the dipstick
-
If oil level has dropped, add more oil - this is normal,
-
-
-
Place funnel into oil container
-
Pour the old oil into the recently-emptied oil container
-
Mark the oil container as "old" and return to a mechanic shop for recycling
-
Drive off into the sunset
Enjoy a cool beverage (but not while driving off into the sunset)
Drive off into the sunset
Enjoy a cool beverage (but not while driving off into the sunset)
다른 2명이 해당 안내서를 완성하였습니다.
팀
Baylor, Team 4-5, Williams Spring 2015 Baylor, Team 4-5, Williams Spring 2015 회원
BU-WILLIAMS-S15S4G5
4 회원들
안내서 11개 작성하였습니다
댓글 한 개
Excellent guide, very well explained.
Just a comment; I have a 2017 VW Jetta, it is a 2.5 with 5 cylinders and it needs more motor oil than stated.
