소개

This guide will demonstrate how to replace the back camera of a Zenfone 3. This may be necessary if the camera no longer shows a picture or shows a distorted picture. For this guide, you will need the tweezers, Torx T2 screwdriver, a prying tool, and the Phillips #00 screwdriver.

  1. Using a pair of tweezers, pull put the SIM card tray and set it to the side. Using a pair of tweezers, pull put the SIM card tray and set it to the side.
    • Using a pair of tweezers, pull put the SIM card tray and set it to the side.

  2. Remove the two 2 mm screws using a Torx T2 screwdriver.
    • Remove the two 2 mm screws using a Torx T2 screwdriver.

  3. Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone. There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.
    • Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone.

    • There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.

  4. Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.
    • Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.

  5. Peel back the silver tape.
    • Peel back the silver tape.

  6. US$100 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기
  7. Disconnect the battery connections.
    • Disconnect the battery connections.

  8. Pry and remove the battery.
    • Pry and remove the battery.

    • The underside of the battery is adhesive so make sure to pry the battery off gently.

  9. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.
    • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.

  10. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.
    • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.

  11. Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver. Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.
    • Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.

  12. Unplug the two wires at the bottom of the circuit board. Unplug the two wires at the bottom of the circuit board. Unplug the two wires at the bottom of the circuit board.
    • Unplug the two wires at the bottom of the circuit board.

  13. Remove the circuit board.
    • Remove the circuit board.

  14. Unplug the camera. Unplug the camera.
    • Unplug the camera.

결론

To reassemble your device, follow these instructions in reverse order.

Henry Barrett

회원 가입일: 2018년 09월 10일

459 평판

안내서 4개 작성하였습니다

University of Alabama, Team S2-G7, Bedsole Fall 2018 University of Alabama, Team S2-G7, Bedsole Fall 2018 회원

UA-BEDSOLE-F18S2G7

4 회원들

안내서 5개 작성하였습니다

조회 통계:

지난 24시간: 4

지난 7일: 9

지난 30일: 42

전체 시간: 163