기기를 수리하세요 커뮤니티 상점

AlphaSmart Pro Rear Panel Replacement

소개

The rear panel may need to be replaced if it is cracked or damaged.

필요한 것

  1. AlphaSmart Pro Rear Panel Replacement, Separating Panels: 1 단계, 이미지 1/3 AlphaSmart Pro Rear Panel Replacement, Separating Panels: 1 단계, 이미지 2/3 AlphaSmart Pro Rear Panel Replacement, Separating Panels: 1 단계, 이미지 3/3

    • Power off your AlphaSmart Pro device and remove the batteries before beginning disassembly.

    • Remove all eight 1 cm Phillips head screws from the back panel of the AlphaSmart Pro with the Phillips #00 Screwdriver.

    • Carefully separate the front panel from the back panel.

    • Notice that the front and back panels are still connected by a ribbon cable.

    편집

  2. AlphaSmart Pro Rear Panel Replacement, Detaching Ribbon Cable: 2 단계, 이미지 1/3 AlphaSmart Pro Rear Panel Replacement, Detaching Ribbon Cable: 2 단계, 이미지 2/3 AlphaSmart Pro Rear Panel Replacement, Detaching Ribbon Cable: 2 단계, 이미지 3/3

    • To remove the ribbon cable, use the spudger to lift each side of the connector from the socket.

    • Gently pull up on the connector to completely remove the connector from the socket.

    • Remove front panel from the motherboard.

    편집

  3. AlphaSmart Pro Rear Panel Replacement, Prepping Keyboard For Removal: 3 단계, 이미지 1/3 AlphaSmart Pro Rear Panel Replacement, Prepping Keyboard For Removal: 3 단계, 이미지 2/3 AlphaSmart Pro Rear Panel Replacement, Prepping Keyboard For Removal: 3 단계, 이미지 3/3

    • Use the Phillips #00 Screwdriver to remove the four 1 cm screws from each corner of the keyboard.

    • Gently lift the keyboard from the rear panel.

    • Notice that the keyboard is still connected to the motherboard by two ribbon cables.

    편집

  5. AlphaSmart Pro Rear Panel Replacement, Detaching keyboard Ribbon Cables: 4 단계, 이미지 1/3 AlphaSmart Pro Rear Panel Replacement, Detaching keyboard Ribbon Cables: 4 단계, 이미지 2/3 AlphaSmart Pro Rear Panel Replacement, Detaching keyboard Ribbon Cables: 4 단계, 이미지 3/3

    • To remove the ribbon cable, gently pull the connector in the direction of the ribbon cable.

    • Pull the ribbon cable to remove it from the connector.

    • Repeat the exact steps above for the other ribbon cable.

    • While the large connector on the left must be pulled toward you in order to remove the ribbon cable, the smaller connector on the right must be pushed away from you.

    편집

  6. AlphaSmart Pro Rear Panel Replacement: 5 단계, 이미지 1/1

    • Remove keyboard from motherboard.

    편집

  7. AlphaSmart Pro Rear Panel Replacement, Disconnecting Battery Prongs From Battery Compartment: 6 단계, 이미지 1/2 AlphaSmart Pro Rear Panel Replacement, Disconnecting Battery Prongs From Battery Compartment: 6 단계, 이미지 2/2

    • Flip the AlphaSmart Pro over so that the rear panel is facing upward.

    • Using a spludger, carefully disconnect the battery prongs, located in the battery compartment.

    편집

  8. AlphaSmart Pro Rear Panel Replacement, Separating Motherboard From Rear Panel.: 7 단계, 이미지 1/2 AlphaSmart Pro Rear Panel Replacement, Separating Motherboard From Rear Panel.: 7 단계, 이미지 2/2

    • Using a Phillips #00 Screwdriver, remove the four 0.8 cm screws from the motherboard.

    • Carefully lift the motherboard away from the rear panel.

    편집

  9. AlphaSmart Pro Rear Panel Replacement, Removal Of Rear Panel: 8 단계, 이미지 1/1

    • Rear panel is separated from motherboard.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 1명과 함께

Ulysses Ramirez

회원 가입일: 10/13/14

67 평판

안내서 2개 작성하였습니다

배지: 7

배지 +4개 더

팀

Clemson, Team 1-1, Benson Fall 2014 Clemson, Team 1-1, Benson Fall 2014 회원

CLEM-BENSON-F14S1G1

4 회원들

안내서 16개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 6

30일 전: 8

전체 시간: 226