물건을 수리하세요 커뮤니티 상점

Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement

소개

Use this guide to replace the 4-in-1 WiFi/Bluetooth/FM/GPS board on the Amazon Echo Dot 2nd generation. The 4-in-1 is located on the motherboard, so the whole board must be replaced, rather than replacing each individual component.

필요한 것

  1. Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement, 4-in-1 WiFi/Bluetooth/FM/GPS: 1 단계, 이미지 3개 중 1개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement, 4-in-1 WiFi/Bluetooth/FM/GPS: 1 단계, 이미지 3개 중 2개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement, 4-in-1 WiFi/Bluetooth/FM/GPS: 1 단계, 이미지 3개 중 3개

    • Power off and unplug the echo

    • Using the plastic opening tool, peel off the rubber layer on the bottom of the echo

    편집

  2. Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 2 단계, 이미지 3개 중 1개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 2 단계, 이미지 3개 중 2개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 2 단계, 이미지 3개 중 3개

    • Use a T8 screwdriver bit to unscrew the four 1.6mm torx screws

    • Remove the black cylindrical base

    편집

  4. Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 3 단계, 이미지 3개 중 1개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 3 단계, 이미지 3개 중 2개 Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 3 단계, 이미지 3개 중 3개

    • Use the metal spudger to lift the ZIF connector

    • Remove the ribbon cable from the slot

    편집

  5. Amazon Echo Dot 2nd Generation 4-in-1 WiFi/Bluetooth/FM/GPS Replacement: 4 단계, 이미지 1개 중 1개

    • Remove the motherboard

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 8명이 해당 안내서를 완성하였습니다.

작성자

3다른 기여자 명과 함께

Alexis White

회원 가입일: 10/09/17

577 평판

안내서 2개를 작성함

배지: 9

배지 +6개 더

팀

USF Tampa, Team S1-G3, Leahy Fall 2017 USF Tampa, Team S1-G3, Leahy Fall 2017 회원

USFT-LEAHY-F17S1G3

3 회원들

안내서 12개를 작성함

2가이드 댓글

Where can I find the part my dot won’t connect and I have been going crazy trying to find the motherboard

Ivy Bowman - 답글

I wish to recommend not removing the adhesive layer if you plan to reassemble this Echo Dot. I would suggest poking holes to reach the four screws instead. Then reassembly can reuse the same adhesive layer.

rayramirez - 답글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 8

지난 30일: 44

전체 시간: 7,158