기기를 수리하세요 커뮤니티 상점

Anker 2.4G Wireless Mouse Scroll Wheel Replacement

소개

If your Anker 2.4 G Wireless Mouse scroll wheel is not working properly it may need to be cleaned or replaced. Over time dust can build-up in the mouse causing issues with scrolling, this can be resolved with a simple clean. If there is hardware damage, the scroll wheel may need to be replaced.

This guide will show you how to disassemble your Anker 2.4 G Wireless Mouse to repair the scroll wheel with little to no experience required.

For help with desoldering, see: How To Solder and Desolder Connections

필요한 것

  1. Anker 2.4G Wireless Mouse Scroll Wheel Replacement, Scroll Wheel: 1 단계, 이미지 1/1

    • Remove the stickers from the bottom of the mouse to have access to the screws, The stickers are shown in the picture by the red rectangles.

    편집

  2. Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 2 단계, 이미지 1/1

    • Use a Phillips #00 to remove the 4 screws shown by the red circles in the picture.

    편집

  4. Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 3 단계, 이미지 1/2 Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 3 단계, 이미지 2/2

    • Using a plastic opening tool or spudger, on the center of the mouse, separate the upper and lower board.

    편집

  5. Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 4 단계, 이미지 1/1

    • Remove the wires from the white crimp headers, separating the upper and lower housing units of the mouse. Avoid pulling the wires too hard to prevent them from breaking.

    • Don't pull the wires too hard, as they might break.

    편집

  6. Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 5 단계, 이미지 1/2 Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 5 단계, 이미지 2/2

    • Pull the scroll wheel put parallel to the board.

    • This may take some force to remove. Pull the scroll wheel out parallel to the board rather than perpendicular to it.

    • Replace/clean if needed.

    • If your mouse still does not work after this step, then continue to the next instruction.

    편집

  7. Anker 2.4G Wireless Mouse Scroll Wheel Replacement: 6 단계, 이미지 1/1

    • Desolder the three pins, then solder in the replacement part.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 12명과 함께

Vincent Lee

회원 가입일: 01/23/14

361 평판

안내서 3개 작성하였습니다

배지: 9

배지 +6개 더

팀

Cal Poly, Team 1-39, Maness Winter 2014 Cal Poly, Team 1-39, Maness Winter 2014 회원

CPSU-MANESS-W14S1G39

4 회원들

안내서 16개 작성하였습니다

댓글 한 개

Hi Vincent, could you please help me with finding a place where this rotation sensor can be bought. I'm not even sure how this part is called so searching for it is quite tricky.

Cheers,

Michal

Michal Rorat - 답글

댓글 쓰기

조회 통계:

24 시간 전: 3

7일 전: 9

30일 전: 36

전체 시간: 8,448