소개

The LCD main board is the backbone of the Apple Studio Display M2454. It accepts the information coming from the computer and transmits this data to the screen to form an image. The main board is also wired into the USB ports on the back of the monitor and other circuitry. There are many connections but replacing this board is relatively easy.

부품

부품은 필요하지 않습니다.

Locate the four hex head screws located on the corners of the back panel.
  • Locate the four hex head screws located on the corners of the back panel.

    • Remove the screws with a 2mm hex screwdriver.

댓글 쓰기

Locate the three 2mm hex screws located on the back stand of the monitor.
  • Locate the three 2mm hex screws located on the back stand of the monitor.

    • These screws must be removed with the 2mm hex screwdriver in order for the back panel to be removed.

댓글 쓰기

Pull the clear back panel cover off.
  • Pull the clear back panel cover off.

  • Be sure to feed the cable through the back panel so no damage occurs.

댓글 쓰기

Now remove the back panel under the clear cover.
  • Now remove the back panel under the clear cover.

  • Again, feed the cable through the panel so no damage occurs.

댓글 쓰기

Remove the phillips head screw holding the back panel spacer with the phillips head screwdriver.
  • Remove the phillips head screw holding the back panel spacer with the phillips head screwdriver.

댓글 쓰기

아버지의 날 선물 안내
아버지 뿐만 아니라 다른 분들도 존중합시다—우리에게 수리하는 법을 가르쳐 주신 모든 멘토를 축하합시다.
아버지의 날 선물 안내
우리에게 수리하는 법을 가르쳐 주신 사람들을 존중합시다.
Remove the two phillips head screws near the cable attachment with the phillips head screwdriver.
  • Remove the two phillips head screws near the cable attachment with the phillips head screwdriver.

댓글 쓰기

To remove the metal plate covering the circuitry you need to push the cover towards the base of the monitor.
  • To remove the metal plate covering the circuitry you need to push the cover towards the base of the monitor.

  • If done correctly the tabs holding the plate should be detached and the plate will easily pop off.

댓글 쓰기

Now that the circuitry is exposed the boards can be seen and replaced.
  • Now that the circuitry is exposed the boards can be seen and replaced.

  • The LCD Main Board is the largest board in the center of the device with seven external connections.

댓글 쓰기

Locate the four phillips head screws on the corners of the board.
  • Locate the four phillips head screws on the corners of the board.

  • Using the phillips head screwdriver, remove the four screws holding the board to the monitor.

댓글 쓰기

Remove the four braided connections simply by pushing the side of the connectors in and pull out.
  • Remove the four braided connections simply by pushing the side of the connectors in and pull out.

댓글 쓰기

Remove the other two connectors by raising the tab on each either by hand or using a flat ended tool as shown.
  • Remove the other two connectors by raising the tab on each either by hand or using a flat ended tool as shown.

  • Then gently pull away from the board to release tabs.

  • The tabs can easily break off, be extra careful.

댓글 쓰기

Remove the final black connector by pressing down on the back of the tab on the connector and then pull away from the board.
  • Remove the final black connector by pressing down on the back of the tab on the connector and then pull away from the board.

  • Be careful when holding onto the board while removing this connector or you risk pulling the board away too quickly and damaging the connector.

댓글 쓰기

With all the connectors removed the board can be lifted away.
  • With all the connectors removed the board can be lifted away.

  • Now the new board can be attached by following the previous steps in reverse.

댓글 쓰기

결승점

다른 한 분이 해당 안내서를 완성하였습니다.

Dylan Perry

회원 가입일: 2010년 01월 20일

129 평판

안내서 5개 작성하였습니다

Cal Poly, Team 13-27, Maness Winter 2010 Cal Poly, Team 13-27, Maness Winter 2010 회원

CPSU-MANESS-W10S13G27

4 회원들

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 5

전체 시간: 3,042