기기를 수리하세요 커뮤니티 상점

Astak Mole Camera Head Replacement

소개

In order for you to replace the camera head, you will have to separate the base and the camera head by disconnecting some wires that lead from the head to the motherboard.

필요한 것

  1. Astak Mole Camera Head Replacement, Lower Case: 1 단계, 이미지 1/1

    • Remove the four bottom tabs in order to access the bottom screws.

    편집

  2. Astak Mole Camera Head Replacement: 2 단계, 이미지 1/1

    • Remove all four 14 mm Phillips #1 screws.

    편집

  3. Astak Mole Camera Head Replacement: 3 단계, 이미지 1/1

    • Remove the SD card.

    편집

  5. Astak Mole Camera Head Replacement: 4 단계, 이미지 1/1

    • Pry up the motherboard on the four points using a spudger.

    • The regular black nylon spudger should be used whenever possible, especially around sensitive internal components.

    편집

  6. Astak Mole Camera Head Replacement: 5 단계, 이미지 1/1

    • Gently pull back the motherboard to expose many of the component's wired connections.

    편집

  7. Astak Mole Camera Head Replacement, Camera Head: 6 단계, 이미지 1/1

    • Unscrew the three screws connecting the base to the camera head with the PH1 size Phillips head bit.

    • Screw measurements: Length=7.0mm.

    • The third screw can be exposed by rotating the camera head.

    • Do not force the camera head farther than it will allow you.

    편집

  8. Astak Mole Camera Head Replacement: 7 단계, 이미지 1/1

    • Unscrew indicated Phillips head screws using the PH1 Phillips head bit to free wires.

    • Screw measurements: Length=3.5mm

    편집

  9. Astak Mole Camera Head Replacement: 8 단계, 이미지 1/3 Astak Mole Camera Head Replacement: 8 단계, 이미지 2/3 Astak Mole Camera Head Replacement: 8 단계, 이미지 3/3

    • Separate the three indicated outputs from the motherboard with metal spudger.

    • There is electrical adhesive on the output. This can be easily separated with the metal spudger.

    • The regular black nylon spudger should be used whenever possible, especially around sensitive internal components.

    편집

  10. Astak Mole Camera Head Replacement: 9 단계, 이미지 1/1

    • Separate the wire from CPU by cutting adhesive with metal spudger.

    • It is advised to reapply adhesive to wired connections during reassembly, and to re-attach wires to CPU to prevent disconnection and loose wires inside device.

    • Be careful not to damage the CPU in the process. This is not a wired connection.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 5명과 함께

Bryan

회원 가입일: 09/15/16

104 평판

안내서 1개 작성함

배지: 4

+1개 배지 추가

팀

USF Tampa, Team 2-2, Blackwell Fall 2016 USF Tampa, Team 2-2, Blackwell Fall 2016 회원

USFT-BLACKWELL-F16S2G2

4 회원들

안내서 12개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 6

30일 전: 12

전체 시간: 468