Asus TUF Gaming FX505DY Motherboard Replacement

1 단계 Back Case

• Turn off the laptop.
• Disconnect the charging cable.
• Failure to disconnect the charging cable and power down the computer could result in personal or property damage.
• Flip the laptop so the back is facing up.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
2 단계



• Use a Phillips #1 screwdriver to remove the five 6 mm screws that secure the back panel.
• Use the same screwdriver to remove the six 13 mm screws securing the back panel.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
3 단계
• Insert the plastic opening tool at a corner and pry up along the edges, leaving the back side with the hinges for last.
• Do not insert the opening tool too far into the laptop to avoid damaging internal components.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
4 단계
• Gently lift up the back panel to release any remaining clips on the side with the hinges and remove the panel.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
5 단계 Motherboard
• With a Phillips 0-bit screwdriver, remove eight 5.0 mm screws on the silver brackets
• With a Phillips 0-bit screwdriver, remove two 5.0 mm screws holding the edge of the fans in place
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
6 단계
• Gently remove all power cables connecting the fans to the motherboard.
• Once all cables and screws are removed, carefully lift up and remove the fans and heat sink
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
7 단계
• With a Phillips 0-bit screwdriver, unscrew four 5.0 mm screws.
• Disconnect the primary connector cable located at the bottom left and carefully remove the module.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
8 단계
• Removing the ram, push down unto the ram and move the metal locking tabs to the side by lifting upward slightly then moving each to their outside.
• Pull the ram out toward the angle when the ram is sticking up at an angle when released.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
9 단계
• With a Phillips 0-bit screwdriver, unscrew four 5.0 mm top screws holding the hard drive in place.
• Pinch the top left corner with your finger and slide the harddrive out of its casing.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
10 단계
• With a Phillips 0-bit screwdriver, unscrew two 5.0 mm screws holding SSD down to the motherboard on the right side of the board
• Slide module out of protective casing to remove piece.
편집
댓글 달기
댓글 달기
댓글 쓰기
1024
취소 댓글 달기
11 단계
• With a size 0 Phillips screwdriver, unscrew three center 5 mm screws securing the board in place.
• Carefully lift the board and place in a safe area.
편집
댓글 한 개
댓글 달기
댓글 쓰기
1024
취소 댓글 달기

작성자

다른 기여자 4명과 함께

Sebastian Frederick Klincewicz

회원 가입일: 10/04/22

394 평판

안내서 3개 작성하였습니다

배지: 7

• 
• 
• 

배지 +4개 더

팀

The Citadel Military College of South Carolina, Team 3-19, Eggleston Fall 2022 The Citadel Military College of South Carolina, Team 3-19, Eggleston Fall 2022 회원

CMCSC-EGGLESTON-F22S3G19

2 회원들

안내서 3개 작성하였습니다

해당 안내서 넣기

해당 안내서를 사이트/포럼에 작은 위젯으로 포함하려면 크기를 선택하고 아래 코드를 복사하십시오.

미리보기