메인 콘텐츠로 스킵하기

소개

This guide will help you replace a defective screen, patience and extreme care is required. It will require a major disassembly of the laptop.

  1. Make sure the computer is turned off.
    • Make sure the computer is turned off.

    • Flip the device over so that the back cover is facing you.

  2. Remove the four 5mm Phillips #1 screws from the top of the laptop. Remove the two 6mm Phillips #1 screws from the sides of the laptop.
    • Remove the four 5mm Phillips #1 screws from the top of the laptop.

    • Remove the two 6mm Phillips #1 screws from the sides of the laptop.

    • Remove the four 2mm Phillips #1 screws from the bottom of the laptop.

  3. Use a plastic opening tool to gently pry the bottom of the laptop up. Slowly slide it along the edges, twisting it every so often to pop the bottom of the laptop out of the clips holding it in place. Use a plastic opening tool to gently pry the bottom of the laptop up. Slowly slide it along the edges, twisting it every so often to pop the bottom of the laptop out of the clips holding it in place. Use a plastic opening tool to gently pry the bottom of the laptop up. Slowly slide it along the edges, twisting it every so often to pop the bottom of the laptop out of the clips holding it in place.
    • Use a plastic opening tool to gently pry the bottom of the laptop up. Slowly slide it along the edges, twisting it every so often to pop the bottom of the laptop out of the clips holding it in place.

  4. Lift off the cover and remove the back cover from the device.
    • Lift off the cover and remove the back cover from the device.

  5. Unplug the screen connector from the motherboard. Unplug the screen connector from the motherboard. Unplug the screen connector from the motherboard.
    • Unplug the screen connector from the motherboard.

  6. Using a Phillips #1 Screwdriver unscrew the four 4 mm screws holding the screen holder onto the motherboard. Using a Phillips #1 Screwdriver unscrew the four 4 mm screws holding the screen holder onto the motherboard.
    • Using a Phillips #1 Screwdriver unscrew the four 4 mm screws holding the screen holder onto the motherboard.

  7. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now
  8. Remove the two cables connecting to the wifi card. Remove the two cables connecting to the wifi card. Remove the two cables connecting to the wifi card.
    • Remove the two cables connecting to the wifi card.

  9. Remove the screen holder from the rest of the laptop. Make sure when removing screen cover lift bottom of the laptop to about a 45° degree angle when removing it. Make sure when removing screen cover lift bottom of the laptop to about a 45° degree angle when removing it.
    • Remove the screen holder from the rest of the laptop.

    • Make sure when removing screen cover lift bottom of the laptop to about a 45° degree angle when removing it.

  10. Remove the bottom of the laptop from the screen. Remove the bottom of the laptop from the screen.
    • Remove the bottom of the laptop from the screen.

  11. Remove the hinge cover by gently pulling to the right then upwards. Remove the hinge cover by gently pulling to the right then upwards. Remove the hinge cover by gently pulling to the right then upwards.
    • Remove the hinge cover by gently pulling to the right then upwards.

  12. Using a Phillips #1 Screwdriver unscrew the six 3 mm black screws and the three 2 mm copper screws that are keeping the screen in place.
    • Using a Phillips #1 Screwdriver unscrew the six 3 mm black screws and the three 2 mm copper screws that are keeping the screen in place.

    • Keep track of what screws go where.

  13. Push screen downwards then pull top of screen upwards and remove the screen. Push screen downwards then pull top of screen upwards and remove the screen. Push screen downwards then pull top of screen upwards and remove the screen.
    • Push screen downwards then pull top of screen upwards and remove the screen.

  14. Using a Phillips #1 Screwdriver Unscrew the four 2 mm screws holding the screen onto the screen cover. Use the PH0 bit screwdriver to unscrew the screws.
    • Using a Phillips #1 Screwdriver Unscrew the four 2 mm screws holding the screen onto the screen cover.

    • Use the PH0 bit screwdriver to unscrew the screws.

  15. Use a sharp object to remove tape from the back of the screen. Careful when cutting the tape off, you can accidentally cut a wire Careful when cutting the tape off, you can accidentally cut a wire
    • Use a sharp object to remove tape from the back of the screen.

    • Careful when cutting the tape off, you can accidentally cut a wire

  16. Unplug the screen from the screen holder. Don't pull the cable too hard or it can damage the connection. Don't pull the cable too hard or it can damage the connection.
    • Unplug the screen from the screen holder.

    • Don't pull the cable too hard or it can damage the connection.

  17. Take the screen off of the screen holder. Take the screen off of the screen holder. Take the screen off of the screen holder.
    • Take the screen off of the screen holder.

결론

To reassemble your device, follow these instructions in reverse order.

Jorge Villarreal

회원 가입일: 2017년 10월 02일

301 평판

안내서 3개 작성하였습니다

USF Tampa, Team S10-G3, Thompson Fall 2017 USF Tampa, Team S10-G3, Thompson Fall 2017 회원

USFT-THOMPSON-F17S10G3

4 회원들

안내서 6개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 3

지난 7일: 6

지난 30일: 34

전체 시간: 444