메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Audiovox CDM-8900 Logic Board Replacement

작성자 Aaron Shaw (또 다른 기여자 7명)
  • 댓글 0
  • 즐겨찾기 3
  • 완료: 1

난이도

보통

단계

5

소요 시간

5 분

섹션

3

플래그

5

Needs Better Images

더 나은 이미지가 필요함

더 나은 사진은 해당 안내서를 향상시킬 것입니다. 사진 촬영, 편집, 또는 새로운 업로드를 도와주십시오!

Grammar Police

문법 검토

회원님 내면의 영어 교사를 인정하고 해당 안내서의 문법 향상에 도움을 주십시오!

Inconsistent Images

일관성 없는 이미지

해당 안내서의 이미지를 전제 조건들과 더욱 일관성 있게 업데이트하는 것은 안내서의 멋짐이 향상될 것입니다.

Confusing Text

헷갈리는 텍스트

해당 안내서의 어떤 텍스트는 헷갈리며, 중복되었거나 주제에서 벗어났습니다. 편집하여 명확하게 하여 주십시오!

Missed a Step

한 단계 누락

이런! 해당 안내서는 현재 몇몇 중요한 단계가 빠져 있습니다.

소개

This is how to remove the 5 screws and pry the logic board free.

도구

해당 도구 구매

부품

부품은 필요하지 않습니다.

  1. Hold the phone in one hand, slide latch, and pull to remove the battery. Hold the phone in one hand, slide latch, and pull to remove the battery.

    • Hold the phone in one hand, slide latch, and pull to remove the battery.

    편집

  2. Grasp antenna at its base and unscrew. Remove the antenna along with its plastic casing from inside the battery housing. Keep the antenna in the plastic casing for reassembly. Remove the antenna along with its plastic casing from inside the battery housing. Keep the antenna in the plastic casing for reassembly.

    • Grasp antenna at its base and unscrew.

    • Remove the antenna along with its plastic casing from inside the battery housing. Keep the antenna in the plastic casing for reassembly.

    편집

  3. US$100.00 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기

  4. Remove small rubber insert from top of phone to access the top screw. Warning: Screws are very small and may be difficult to see while unscrewing. Unscrew all five (5) screws on the back of cell phone.

    • Remove small rubber insert from top of phone to access the top screw.

    • Warning: Screws are very small and may be difficult to see while unscrewing.

    • Unscrew all five (5) screws on the back of cell phone.

    • If screws do not remove after fully unthreading, gently invert and tap phone in hand until the screws come loose.

    편집

  5. Wedge back plate away from cell phone using the leverage from the plastic spudger. The volume control button on the left side of the phone will be loose. Make sure to carefully reinsert during reassembly. Detach logic board from LCD screen connector by gently detaching the small copper plate on the top right of the logic board. (shown circled in blue and detached)

    • Wedge back plate away from cell phone using the leverage from the plastic spudger.

    • The volume control button on the left side of the phone will be loose. Make sure to carefully reinsert during reassembly.

    • Detach logic board from LCD screen connector by gently detaching the small copper plate on the top right of the logic board. (shown circled in blue and detached)

    편집

  6. Pop the logic board out from the front of the cell phone. Before reassembly, be sure keypad is lined up with logic board. Before reassembly, be sure camera lens is properly aligned at the top of the logic board and volume controls are in place.

    • Pop the logic board out from the front of the cell phone.

    • Before reassembly, be sure keypad is lined up with logic board.

    • Before reassembly, be sure camera lens is properly aligned at the top of the logic board and volume controls are in place.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Aaron Shaw

회원 가입일: 2010년 04월 15일

150 평판

안내서 6개 작성하였습니다

배지: 6

배지 +3개 더

팀

Cal Poly, Team 28-31, Regan Spring 2010 Cal Poly, Team 28-31, Regan Spring 2010 회원

CPSU-REGAN-S10S28G31

4 회원들

안내서 12개 작성하였습니다

댓글 0개

의견 추가하세요
조회 통계:

지난 24시간: 0

지난 7일: 2

지난 30일: 2

전체 시간: 2,592