기기를 수리하세요 커뮤니티 상점

Bell and Howell DNV16HDZ Internal Screen Replacement

필요한 것

  1. Bell and Howell DNV16HDZ Internal Screen Replacement, Lens Assembly: 1 단계, 이미지 1/2 Bell and Howell DNV16HDZ Internal Screen Replacement, Lens Assembly: 1 단계, 이미지 2/2

    • Remove the five 30mm Phillips #0 screws on the bottom of the camera.

    번역하기

  2. Bell and Howell DNV16HDZ Internal Screen Replacement: 2 단계, 이미지 1/1

    • Use a plastic opening tool to disconnect the internal hinges that snaps the camera into place.

    • Using a plastic opening tool is important since a metal one will scratch or damage the thin plastic hinges that hold the camera together.

    번역하기

  3. Bell and Howell DNV16HDZ Internal Screen Replacement: 3 단계, 이미지 1/1

    • It will still be connected by a plastic film. This can also be disconnected by pulling up the white part where it connects to the light circuit board.

    번역하기

  5. Bell and Howell DNV16HDZ Internal Screen Replacement, Internal Screen: 4 단계, 이미지 1/1

    • Pull the side with the hand strap upwards to disconnect it from the camcorder.

    번역하기

  6. Bell and Howell DNV16HDZ Internal Screen Replacement: 5 단계, 이미지 1/2 Bell and Howell DNV16HDZ Internal Screen Replacement: 5 단계, 이미지 2/2

    • Remove the battery.

    • Remove the four 30 mm Phillips #0 screws on the back.

    번역하기

  7. Bell and Howell DNV16HDZ Internal Screen Replacement: 6 단계, 이미지 1/3 Bell and Howell DNV16HDZ Internal Screen Replacement: 6 단계, 이미지 2/3 Bell and Howell DNV16HDZ Internal Screen Replacement: 6 단계, 이미지 3/3

    • On the hinge of the camcorder remove the two 30 mm Phillips #0 screws.

    • Remove blue piece holding it together.

    • Remove the 50 mm Phillips #0 screw.

    번역하기

  8. Bell and Howell DNV16HDZ Internal Screen Replacement: 7 단계, 이미지 1/2 Bell and Howell DNV16HDZ Internal Screen Replacement: 7 단계, 이미지 2/2

    • Use the plastic opening tool and slowly pry open the side.

    • Now pull the part with camcorder out.

    • There is a wire connecting these two pieces using to much force will damage the camcorder.

    번역하기

  9. Bell and Howell DNV16HDZ Internal Screen Replacement: 8 단계, 이미지 1/3 Bell and Howell DNV16HDZ Internal Screen Replacement: 8 단계, 이미지 2/3 Bell and Howell DNV16HDZ Internal Screen Replacement: 8 단계, 이미지 3/3

    • Have the screen open and twist it 90 degrees unscrew the 40 mm screw.

    • Repeat for the other side.

    • Use the plastic opening tool to pry the outer part of the screen, now attach the new one.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 2명과 함께

Jerry Hadjah

회원 가입일: 03/04/16

525 평판

안내서 5개 작성하였습니다

배지: 10

배지 +7개 더

팀

UMass Dartmouth, Team 8-4, Botvin Spring 2016 UMass Dartmouth, Team 8-4, Botvin Spring 2016 회원

UMASSD-BOTVIN-S16S8G4

3 회원들

안내서 12개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 3

30일 전: 13

전체 시간: 332