메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Bissell SpotBot Pet Repair Brush Motor Replacement

작성자 Anthony Bonvino (또 다른 기여자 4명)
  • 댓글 1
  • 즐겨찾기 1
  • 완료: 3

난이도

보통

단계

11

소요 시간

시간 제안??

섹션

1

플래그

2

Confusing Text

헷갈리는 텍스트

해당 안내서의 어떤 텍스트는 헷갈리며, 중복되었거나 주제에서 벗어났습니다. 편집하여 명확하게 하여 주십시오!

Needs Better Images

더 나은 이미지가 필요함

더 나은 사진은 해당 안내서를 향상시킬 것입니다. 사진 촬영, 편집, 또는 새로운 업로드를 도와주십시오!

소개

This replacement guide will cover how to replace the brush motor on the Bissell SpotBot Pet carpet cleaner.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Set your Bissell SpotBot Pet on a flat surface to begin your repair.

    • Set your Bissell SpotBot Pet on a flat surface to begin your repair.

    편집

  2. Lift straight up on the right container to remove it from the vacuum.

    • Lift straight up on the right container to remove it from the vacuum.

    편집

  3. Lift up on the tab on the top of the vacuum and then lift straight up on the left container to remove it. Lift up on the tab on the top of the vacuum and then lift straight up on the left container to remove it.

    • Lift up on the tab on the top of the vacuum and then lift straight up on the left container to remove it.

    편집

  4. Remove the vacuum tube by sliding it out of its holder on the side.

    • Remove the vacuum tube by sliding it out of its holder on the side.

    편집

  5. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

  6. Unscrew the 4 screws on the top of the device and gently lift the top half up. A ribbon cable is still attached to the underside of the top half.

    • Unscrew the 4 screws on the top of the device and gently lift the top half up.

    • A ribbon cable is still attached to the underside of the top half.

    편집

  7. Unplug the ribbon cable connecting the bottom half to the control panel on the top half. Set the top off to the side. Unplug the ribbon cable connecting the bottom half to the control panel on the top half. Set the top off to the side. Unplug the ribbon cable connecting the bottom half to the control panel on the top half. Set the top off to the side.

    • Unplug the ribbon cable connecting the bottom half to the control panel on the top half. Set the top off to the side.

    편집

  8. Unscrew the screw next to the white plastic wiring harness box. This will allow you to set the box off to the side. Unscrew the screw next to the white plastic wiring harness box. This will allow you to set the box off to the side.

    • Unscrew the screw next to the white plastic wiring harness box. This will allow you to set the box off to the side.

    편집

  9. Unscrew the screws on the plastic holder on the right side of the device. Remove the plastic holder from the vacuum.

    • Unscrew the screws on the plastic holder on the right side of the device. Remove the plastic holder from the vacuum.

    • Unscrew the screws that mount the vacuum motor to the device

    편집

  10. Unplug the wires connecting the motor to the wiring harness. Unplug the wires connecting the motor to the wiring harness.

    • Unplug the wires connecting the motor to the wiring harness.

    편집

  11. Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum. Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum.

    • Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum.

    편집

  12. Remove the screws for the brush motor. This motor controls the automatic scrubbing mechanism. Remove the screws for the brush motor. This motor controls the automatic scrubbing mechanism.

    • Remove the screws for the brush motor. This motor controls the automatic scrubbing mechanism.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Anthony Bonvino

회원 가입일: 2017년 09월 26일

323 평판

안내서 2개 작성하였습니다

배지: 12

배지 +9개 더

팀

Cal Poly, Team S7-G3, Banghart Fall 2017 Cal Poly, Team S7-G3, Banghart Fall 2017 회원

CPSU-BANGHART-F17S7G3

4 회원들

안내서 2개 작성하였습니다

댓글 한 개

의견 추가하세요

hi i think you did an amazing job of breaking down how to disasemble this spotbot. i have the exact same one and though it works great suction is amazing, the brushes dont spin and i took it apart completely except i didnt know where the motor was that controlled the brushes until reading this. thanks so much

art - 답글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 3

지난 30일: 10

전체 시간: 374