기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Black and Decker BL3000S Circuit Board

필요한 것

  1. Black and Decker BL3000S Circuit Board, Blender Base: 1 단계, 이미지 1/2 Black and Decker BL3000S Circuit Board, Blender Base: 1 단계, 이미지 2/2

    • Before disassembling the blender base, make sure the blender disconnected from any power outlet.

    • Lift the jar straight up from the base without tilting the jar.

    번역하기

  2. Black and Decker BL3000S Circuit Board: 2 단계, 이미지 1/1

    • Remove the top three 1/4 inch base screws using a Philip's head screwdriver.

    번역하기

  3. Black and Decker BL3000S Circuit Board: 3 단계, 이미지 1/2 Black and Decker BL3000S Circuit Board: 3 단계, 이미지 2/2

    • Remove the two base leg covers next to the power cord using pliers or a flat-head screwdriver.

    • This provides access to the base screws beneath.

    번역하기

  5. Black and Decker BL3000S Circuit Board: 4 단계, 이미지 1/1

    • Remove the following screws that secure the top and bottom halves of the base.

    • One 1/4 Phillips screw

    • One TA-20 screw

    • Both screwdrivers must have a minimum of a three inch shank (length).

    • Screwdrivers with extenders will not fit down the access holes.

    번역하기

  6. Black and Decker BL3000S Circuit Board: 5 단계, 이미지 1/1

    • Lift the top half of the base from the bottom half of the base to reveal the internal mechanism.

    번역하기

  7. Black and Decker BL3000S Circuit Board, Circuit Board: 6 단계, 이미지 1/1

    • Once you have the base removed, the circuit board should be clearly visible inside.

    번역하기

  8. Black and Decker BL3000S Circuit Board: 7 단계, 이미지 1/2 Black and Decker BL3000S Circuit Board: 7 단계, 이미지 2/2

    • Remove the four screws located on the circuit board.

    • Two are on the left side.

    • Two are on the right side.

    번역하기

  9. Black and Decker BL3000S Circuit Board: 8 단계, 이미지 1/1

    • Remove the following soldered connections with a soldering iron:

    • Motor wires

    • Power cord wires

    번역하기

  10. Black and Decker BL3000S Circuit Board: 9 단계, 이미지 1/1

    • Lift the circuit board straight up to remove it from the base.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Andrew

회원 가입일: 10/04/12

209 평판

안내서 4개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 6-34, Regan Fall 2012 Cal Poly, Team 6-34, Regan Fall 2012 회원

CPSU-REGAN-F12S6G34

4 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 9

30일 전: 35

전체 시간: 4,672