기기를 수리하세요 커뮤니티 상점

Black and Decker BL3000S button panel replacement

소개

You will need to have completed the prerequisite guides prior to this guide in order to execute it.

필요한 것

  1. Black and Decker BL3000S button panel replacement, Blender Base: 1 단계, 이미지 1/2 Black and Decker BL3000S button panel replacement, Blender Base: 1 단계, 이미지 2/2

    • Before disassembling the blender base, make sure the blender disconnected from any power outlet.

    • Lift the jar straight up from the base without tilting the jar.

    번역하기

  2. Black and Decker BL3000S button panel replacement: 2 단계, 이미지 1/1

    • Remove the top three 1/4 inch base screws using a Philip's head screwdriver.

    번역하기

  3. Black and Decker BL3000S button panel replacement: 3 단계, 이미지 1/2 Black and Decker BL3000S button panel replacement: 3 단계, 이미지 2/2

    • Remove the two base leg covers next to the power cord using pliers or a flat-head screwdriver.

    • This provides access to the base screws beneath.

    번역하기

  4. Black and Decker BL3000S button panel replacement: 4 단계, 이미지 1/1

    • Remove the following screws that secure the top and bottom halves of the base.

    • One 1/4 Phillips screw

    • One TA-20 screw

    • Both screwdrivers must have a minimum of a three inch shank (length).

    • Screwdrivers with extenders will not fit down the access holes.

    번역하기

  6. Black and Decker BL3000S button panel replacement: 5 단계, 이미지 1/1

    • Lift the top half of the base from the bottom half of the base to reveal the internal mechanism.

    번역하기

  7. Black and Decker BL3000S button panel replacement, Circuit Board: 6 단계, 이미지 1/1

    • Once you have the base removed, the circuit board should be clearly visible inside.

    번역하기

  8. Black and Decker BL3000S button panel replacement: 7 단계, 이미지 1/2 Black and Decker BL3000S button panel replacement: 7 단계, 이미지 2/2

    • Remove the four screws located on the circuit board.

    • Two are on the left side.

    • Two are on the right side.

    번역하기

  9. Black and Decker BL3000S button panel replacement: 8 단계, 이미지 1/1

    • Remove the following soldered connections with a soldering iron:

    • Motor wires

    • Power cord wires

    번역하기

  10. Black and Decker BL3000S button panel replacement: 9 단계, 이미지 1/1

    • Lift the circuit board straight up to remove it from the base.

    번역하기

  11. Black and Decker BL3000S button panel replacement, Buttons: 10 단계, 이미지 1/1

    • Once the circuit board has been freed from its screws it can be moved out of the way to gain access to the buttons.

    • A single screw must be removed from the top as shown.

    번역하기

  12. Black and Decker BL3000S button panel replacement: 11 단계, 이미지 1/1

    • Push firmly from the outside of the blender on the face of the buttons to pop it out of its locked position.

    번역하기

  13. Black and Decker BL3000S button panel replacement: 12 단계, 이미지 1/2 Black and Decker BL3000S button panel replacement: 12 단계, 이미지 2/2

    • Provided is a front and a back view of a functioning button frame from the BL3000S.

    • Check for cracks, bends, debris, or missing extentions and fastens.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Austin Abernathy

회원 가입일: 10/05/12

18 평판

안내서 1개 작성함

배지: 3

팀

Cal Poly, Team 6-34, Regan Fall 2012 Cal Poly, Team 6-34, Regan Fall 2012 회원

CPSU-REGAN-F12S6G34

4 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 19

전체 시간: 2,374