기기를 수리하세요 커뮤니티 상점

Black and Decker FT1000 Type 1 Blower Switch Replacement

소개

Black and Decker only replaces the switch with a complete motor, so this guide will replace the switch with a commonly available switch.

필요한 것

  1. Black and Decker FT1000 Type 1 Blower Switch Replacement, Black and Decker FT1000 Blower: 1 단계, 이미지 1/2 Black and Decker FT1000 Type 1 Blower Switch Replacement, Black and Decker FT1000 Blower: 1 단계, 이미지 2/2

    • This is the blower. I have removed the nozzle and strap.

    편집

  2. Black and Decker FT1000 Type 1 Blower Switch Replacement: 2 단계, 이미지 1/1

    • Remove Screws.

    편집

  3. Black and Decker FT1000 Type 1 Blower Switch Replacement: 3 단계, 이미지 1/1

    • Remove rear cover. It helps to hold the plug tight to the front housing so the wires stay in place.

    편집

  4. Black and Decker FT1000 Type 1 Blower Switch Replacement: 4 단계, 이미지 1/3 Black and Decker FT1000 Type 1 Blower Switch Replacement: 4 단계, 이미지 2/3 Black and Decker FT1000 Type 1 Blower Switch Replacement: 4 단계, 이미지 3/3

    • Notice the switch is fine, it's simply the plastic armature that is broken.

    • The broken piece is only included with the motor and switch.

    편집

  6. Black and Decker FT1000 Type 1 Blower Switch Replacement: 5 단계, 이미지 1/1

    • This switch is easy to find. It's just a single position single throw switch.

    • I was able to buy it at a home improvement store for $4.00.

    • It even fits nicely in the cutout for the original switch/armature.

    편집

  7. Black and Decker FT1000 Type 1 Blower Switch Replacement: 6 단계, 이미지 1/3 Black and Decker FT1000 Type 1 Blower Switch Replacement: 6 단계, 이미지 2/3 Black and Decker FT1000 Type 1 Blower Switch Replacement: 6 단계, 이미지 3/3

    • Remove the switch/armature.

    • Remove the tension plate (the metal piece).

    • Put in the switch. The terminals are at a bad angle, so we will bend them to fit.

    편집

  8. Black and Decker FT1000 Type 1 Blower Switch Replacement: 7 단계, 이미지 1/2 Black and Decker FT1000 Type 1 Blower Switch Replacement: 7 단계, 이미지 2/2

    • Bend slowly and carefully.

    • Try it in and see how well it fits. It might need some tweaking.

    편집

  9. Black and Decker FT1000 Type 1 Blower Switch Replacement: 8 단계, 이미지 1/2 Black and Decker FT1000 Type 1 Blower Switch Replacement: 8 단계, 이미지 2/2

    • Now remove the actual electrical switch. No need to worry about the wiring, its just open and closed.

    편집

  10. Black and Decker FT1000 Type 1 Blower Switch Replacement: 9 단계, 이미지 1/1

    • The black wire gets a new wider terminal and just plugs on.

    • The other wire needs to be a bit longer, so it gets an extension and a new terminal.

    • I used simple crimp on terminals and splice.

    편집

  11. Black and Decker FT1000 Type 1 Blower Switch Replacement: 10 단계, 이미지 1/2 Black and Decker FT1000 Type 1 Blower Switch Replacement: 10 단계, 이미지 2/2

    • There was not enough room for the terminal to pass by the plastic housing. I just removed a little and then routed the black wire under the switch.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 5명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Scot Henderson

회원 가입일: 05/18/15

857 평판

안내서 2개 작성하였습니다

배지: 9

배지 +6개 더

댓글 3개

This works great. Thank you.

JFGuerrero - 답글

Scot,

Thanks so much for your excellent information!!! The exact same part broke on mine today. I looked at your outstanding detail on what to do. I looked through my stash of stuff and found a toggle switch just like the one you showed but from a different manufacturer. I just got done putting it in as you described and it is better than new now. Works like a champ!

Thanks so much,

John Brodrecht

Casper, WY

John Brodrecht - 답글

This was an excellent post with the perfect amount of detail and clear pictures!

I only wish you had the wiring part in the same detail because I think my wiring is faulty. I will look for your posts again for guidance. Thanks

Julie - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 10

30일 전: 32

전체 시간: 3,355