기기를 수리하세요 커뮤니티 상점

Black and Decker Pivot MAX Motor Replacement

소개

Use this guide to replace a faulty Black and Decker Pivot MAX (Model BDH2000PL) Motor.

The motor is responsible for rotating a fan which creates suction. The motor is the only component that causes motion while running and thus it is the only source of producing any potential noise issues. If the motor is making unusual noise, then it probably has a bad bearing or a damaged impeller. If your device is fully charged and turns on but does not run at all, check for any potential clogs. If nothing is clogged, the motor is likely the issue.

It is recommended that before replacing the motor, ensure the battery and internal wiring is not the damaged. If needed, follow this link to find instruction for replacing the battery. If everything looks fine and the device still does not run, follow this guide to replace the motor.

Make sure to power off your device and disconnect from any external power source prior to beginning this guide.

필요한 것

  1. Black and Decker Pivot MAX Motor Replacement, Battery: 1 단계, 이미지 1/2 Black and Decker Pivot MAX Motor Replacement, Battery: 1 단계, 이미지 2/2

    • Press in and hold the release button.

    • Rotate the dust filter chamber counter-clockwise.

    • Remove the dust filter chamber.

    번역하기

  2. Black and Decker Pivot MAX Motor Replacement: 2 단계, 이미지 1/1

    • Remove the two 10 mm screws from the motor casing with a Phillips #1 screwdriver.

    번역하기

  3. Black and Decker Pivot MAX Motor Replacement: 3 단계, 이미지 1/1

    • Pull the battery cover up and then slide it away from the motor to remove.

    번역하기

  4. Black and Decker Pivot MAX Motor Replacement: 4 단계, 이미지 1/1

    • Remove the battery unit by pulling it out of the main body.

    번역하기

  5. Black and Decker Pivot MAX Motor Replacement: 5 단계, 이미지 1/1

    • Disconnect the quick connect wire harness that connects the motor and battery located in the battery storage compartment.

    번역하기

  6. Black and Decker Pivot MAX Motor Replacement, Pivot Lock Button: 6 단계, 이미지 1/1

    • Remove the handle cover by removing the three PH1 20mm screws

    번역하기

  7. Black and Decker Pivot MAX Motor Replacement: 7 단계, 이미지 1/1

    • Pull out the pivot lock button.

    번역하기

  9. Black and Decker Pivot MAX Motor Replacement, Motor: 8 단계, 이미지 1/2 Black and Decker Pivot MAX Motor Replacement, Motor: 8 단계, 이미지 2/2

    • Gently lift the battery tray from the chassis.

    번역하기

  10. Black and Decker Pivot MAX Motor Replacement: 9 단계, 이미지 1/2 Black and Decker Pivot MAX Motor Replacement: 9 단계, 이미지 2/2

    • Pull the pivot linkage from the handle.

    번역하기

  11. Black and Decker Pivot MAX Motor Replacement: 10 단계, 이미지 1/1

    • Remove the grey handle and set it aside.

    번역하기

  12. Black and Decker Pivot MAX Motor Replacement: 11 단계, 이미지 1/1

    • Remove four Phillips #1 screws from the motor housing.

    번역하기

  13. Black and Decker Pivot MAX Motor Replacement: 12 단계, 이미지 1/1

    • Lift the motor housing straight up to remove it from the rest of the vacuum.

    번역하기

  14. Black and Decker Pivot MAX Motor Replacement: 13 단계, 이미지 1/2 Black and Decker Pivot MAX Motor Replacement: 13 단계, 이미지 2/2

    • Gently pull the red and black wires from the top of the motor.

    번역하기

  15. Black and Decker Pivot MAX Motor Replacement: 14 단계, 이미지 1/1

    • Lift the motor casing from the outer shell of the vacuum by pulling up on the motor casing away from the outer shell.

    번역하기

  16. Black and Decker Pivot MAX Motor Replacement: 15 단계, 이미지 1/2 Black and Decker Pivot MAX Motor Replacement: 15 단계, 이미지 2/2

    • Turn over the motor casing and locate the fan disc underneath where the motor was.

    번역하기

  17. Black and Decker Pivot MAX Motor Replacement: 16 단계, 이미지 1/1

    • Insert one metal spudger underneath the fan disc located on the opposite side of the motor.

    번역하기

  18. Black and Decker Pivot MAX Motor Replacement: 17 단계, 이미지 1/1

    • Use a second metal spudger to pry up the fan disc.

    번역하기

  19. Black and Decker Pivot MAX Motor Replacement: 18 단계, 이미지 1/1

    • Pull up on the fan disc to reveal the motor screws.

    번역하기

  20. Black and Decker Pivot MAX Motor Replacement: 19 단계, 이미지 1/1

    • Remove the two 20mm Phillips #1 screws from the bottom of the motor under the fan disc.

    번역하기

  21. Black and Decker Pivot MAX Motor Replacement: 20 단계, 이미지 1/1

    • Flip over the motor casing and remove the motor to be replaced.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 5명과 함께

Avery Hanulcik

회원 가입일: 09/15/20

316 평판

안내서 2개 작성하였습니다

배지: 8

배지 +5개 더

팀

The Citadel Military College of South Carolina, Team S1-G8, Eggleston Fall 2020 The Citadel Military College of South Carolina, Team S1-G8, Eggleston Fall 2020 회원

CMCSC-EGGLESTON-F20S1G8

3 회원들

안내서 3개 작성하였습니다

댓글 2개

Unbelievable! They sell a replacement motor but not replacement batteries! Wow!

Robert Birmingham - 답글

I needed to access the ultimate exit of the unit to clean and clear the filtration media, but was unsuccessful. Can the issue be clarified? My email address is 8tolive@gmail.com

R. J. W. - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 11

30일 전: 61

전체 시간: 3,311