기기를 수리하세요 커뮤니티 상점

Bowers and Wilkins T7 Battery Replacement

소개

Use this guide to learn how to replace your battery for the Bowers and Wilkins T7 Bluetooth Speaker.

필요한 것

  1. Bowers and Wilkins T7 Battery Replacement, Access Panel: 1 단계, 이미지 1/1

    • As with all electronic devices, make sure your device is powered off before you begin.

    • Gently lift up the access panel; it should easily "pop" open.

    편집

  2. Bowers and Wilkins T7 Battery Replacement: 2 단계, 이미지 1/1

    • Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.

    • There are 8 screws in total.

    편집

  3. Bowers and Wilkins T7 Battery Replacement: 3 단계, 이미지 1/2 Bowers and Wilkins T7 Battery Replacement: 3 단계, 이미지 2/2

    • Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.

    • Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.

    • The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.

    편집

  5. Bowers and Wilkins T7 Battery Replacement: 4 단계, 이미지 1/2 Bowers and Wilkins T7 Battery Replacement: 4 단계, 이미지 2/2

    • The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.

    • Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.

    • As the cover starts to come off, you can lift up using your hand.

    편집

  6. Bowers and Wilkins T7 Battery Replacement: 5 단계, 이미지 1/3 Bowers and Wilkins T7 Battery Replacement: 5 단계, 이미지 2/3 Bowers and Wilkins T7 Battery Replacement: 5 단계, 이미지 3/3
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.

    • While squeezing the internal locking mechanism, pull back the terminal.

    • Repeat this process for the second speaker.

    편집

  7. Bowers and Wilkins T7 Battery Replacement, Battery: 6 단계, 이미지 1/1

    • Using a cutting tool such as a Jimmy steel blade or wire cutter, cut the cable tie surrounding the battery.

    • Be careful not to damage the battery while cutting the cable tie surrounding the battery.

    편집

  8. Bowers and Wilkins T7 Battery Replacement: 7 단계, 이미지 1/2 Bowers and Wilkins T7 Battery Replacement: 7 단계, 이미지 2/2

    • Using the ifixit Opening Tool, pry out the battery power supply connector.

    • Pull and remove the battery power supply connector.

    편집

  9. Bowers and Wilkins T7 Battery Replacement: 8 단계, 이미지 1/2 Bowers and Wilkins T7 Battery Replacement: 8 단계, 이미지 2/2

    • After disconnecting the power supply connector, pull the battery out of its case.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 8명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 2명과 함께

Bertrand Plummer

회원 가입일: 02/28/17

251 평판

안내서 1개 작성함

배지: 6

배지 +3개 더

팀

USF Tampa, Team S7-G1, Cagle Spring 2017 USF Tampa, Team S7-G1, Cagle Spring 2017 회원

USFT-CAGLE-S17S7G1

5 회원들

안내서 4개 작성하였습니다

댓글 3개

Bravo ! Le choix de cet appareil symbolique !

Pierre Vanhoorenbeeck - 답글

Seriously

Couldn't the lady get her

'nails did’

Lux Valet - 답글

No repair any repairing sentar

Abdul Malik Parvez - 답글

댓글 쓰기

조회 통계:

24 시간 전: 4

7일 전: 47

30일 전: 145

전체 시간: 9,466