메인 콘텐츠로 스킵하기

소개

The following step-by-step guide will show how the power button can be located and replaced. The Braven BRV-HD Battery Replacement is a prerequisite for this guide.

  1. Placing the device on its back with the BRV-HD logo facing up, remove the eight 5mm hexagon 2.0 screws on the front panel. Make sure the device is turned off before starting.
    • Placing the device on its back with the BRV-HD logo facing up, remove the eight 5mm hexagon 2.0 screws on the front panel.

    • Make sure the device is turned off before starting.

  2. Lift the front panel off of the speaker using a plastic opening tool.
    • Lift the front panel off of the speaker using a plastic opening tool.

  3. Placing the device with the back panel facing up, remove the eight 5mm hexagon 2.0 screws from the back panel. Placing the device with the back panel facing up, remove the eight 5mm hexagon 2.0 screws from the back panel.
    • Placing the device with the back panel facing up, remove the eight 5mm hexagon 2.0 screws from the back panel.

  4. Lift the back panel off of the device with a plastic opening tool.
    • Lift the back panel off of the device with a plastic opening tool.

  5. Turning the device on its side, unscrew the four 15mm hexagon 2.0 screws on the charging port panel. Turning the device on its side, unscrew the four 15mm hexagon 2.0 screws on the charging port panel.
    • Turning the device on its side, unscrew the four 15mm hexagon 2.0 screws on the charging port panel.

  6. Remove the outer rubber flap and the plastic side port panel.
    • Remove the outer rubber flap and the plastic side port panel.

  7. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  8. Place the device on its front. Loosen the four 12mm Phillips screws in the four corners with a J1 screwdriver.
    • Place the device on its front.

    • Loosen the four 12mm Phillips screws in the four corners with a J1 screwdriver.

    • Loosen the two 8mm Phillips screws in the center with a J1 screwdriver.

    • These screws are difficult to reach and will require a screwdriver extension piece.

  9. Pull off the rubber sleeve surrounding the speaker using your hands.
    • Pull off the rubber sleeve surrounding the speaker using your hands.

    • There is adhesive binding the sleeve to the speaker and force will be required to remove the sleeve.

  10. Lift the black covering off of the speaker using both hands.
    • Lift the black covering off of the speaker using both hands.

    • Loose screws that you were unable to remove with the screwdriver will be removed when you lift off the black covering.

  11. Remove the four 12mm Phillips screws securing the two battery brackets with a J1 screwdriver.
    • Remove the four 12mm Phillips screws securing the two battery brackets with a J1 screwdriver.

    • Move any wires aside to have better access to the screws securing the battery.

  12. Remove the two brackets that hold down the battery using your hands.
    • Remove the two brackets that hold down the battery using your hands.

  13. Use the plastic opening tool to lift up the battery. Remove the battery using your hands.
    • Use the plastic opening tool to lift up the battery.

    • Remove the battery using your hands.

    • The wires connecting the battery to the motherboard are still plugged in. Avoid pulling on the battery or these wires may break.

  14. Disconnect the wire attaching the battery to the motherboard.
    • Disconnect the wire attaching the battery to the motherboard.

    • There is green glue on the wire ports preventing the wires from falling out. Peel and remove this glue as necessary.

    • Be careful when pulling out the wires from their ports. The metal stems attached to the ports can break. A spudger or tweezers may help.

  15. Place the device so the blue button panel is facing up, and use a J00 Phillips J1 head screw driver to remove the two 7mm Phillips head screws on either side of the button panel.
    • Place the device so the blue button panel is facing up, and use a J00 Phillips J1 head screw driver to remove the two 7mm Phillips head screws on either side of the button panel.

  16. Unplug the wire on the inside of the device that connect to the button panel. The wires are fragile.  Do not use excessive force when unplugging the wires from the panel.
    • Unplug the wire on the inside of the device that connect to the button panel.

    • The wires are fragile. Do not use excessive force when unplugging the wires from the panel.

  17. Pry the button panel off of the speaker using a nylon spudger.
    • Pry the button panel off of the speaker using a nylon spudger.

    • A heat gun may be necessary to detach the button panel from the device.

결론

To reassemble your device, follow these instructions in reverse order.

Matthew Nguyen

회원 가입일: 2016년 09월 15일

252 평판

안내서 2개 작성하였습니다

CSU Fullerton, Team 1-5, Bruce Fall 2016 CSU Fullerton, Team 1-5, Bruce Fall 2016 회원

CSUF-BRUCE-F16S1G5

5 회원들

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 7

지난 30일: 27

전체 시간: 707