기기를 수리하세요

수리할 권리

상점

Canon PowerShot A80 Front Cover Replacement

작성자 Travis (또 다른 기여자 6명)
  • 댓글 2
  • 즐겨찾기 0

난이도

쉬움

단계

11

소요 시간

5 분

섹션

2

플래그

3

Inconsistent Images

일관성 없는 이미지

해당 안내서의 이미지를 전제 조건들과 더욱 일관성 있게 업데이트하는 것은 안내서의 멋짐이 향상될 것입니다.

Action Shots

액션 샷

액션 영웅이 되십시오! 해당 안내서는 특정 액션을 더 잘 보여주기 위한 사진들이 필요합니다.

Confusing Text

헷갈리는 텍스트

해당 안내서의 어떤 텍스트는 헷갈리며, 중복되었거나 주제에서 벗어났습니다. 편집하여 명확하게 하여 주십시오!

소개

We will start with the camera intact and take off screws and other parts needed to remove the front cover of the camera

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Remove the three Phillips screws (shown) located at the bottom of the camera.

    • Remove the three Phillips screws (shown) located at the bottom of the camera.

    편집

  2. Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open. Remove the memory card if it is still in the camera.

    • Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open.

    • Remove the memory card if it is still in the camera.

    • Use the Phillips screwdriver to remove the Phillips screw (shown) underneath the memory card slot door.

    편집

  3. Remove the Phillips screw (shown) located inside the top of the memory card compartment.

    • Remove the Phillips screw (shown) located inside the top of the memory card compartment.

    편집

  4. Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down. Remove the batteries from the compartment.

    • Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down.

    • Remove the batteries from the compartment.

    • Unscrew the three Phillips screws (shown) located inside the battery compartment.

    • The screw on the left is longer than the other two.

    편집

  5. OPEN ALL THE TABS

    RAM Upgrade Kits for Mac

    키트 쇼핑하기

    Enough RAM
    For All The Tabs

    키트 쇼핑하기

  6. You should now able to remove the top lid of the camera.

    • You should now able to remove the top lid of the camera.

    • Be cautious of the fragile mylar cable that connects the lid to the main body of the camera.

    • Removing the lid takes a little force. Do this gently. There may be a snapping sound.

    • The door to the memory card compartment will be freed and should be removable now.

    • In other versions of this camera, there is a tab that secures the top from the wrist strap. If yours has this, you won't be able to completely separate the top until you have removed the top screw in Step 8.

    편집

  7. Remove the lower Phillips screw (shown) from the side of the camera.

    • Remove the lower Phillips screw (shown) from the side of the camera.

    • Open the small rubber door below this screw that covers the connectors.

    편집

  8. Open and pivot the LCD screen to its widest open position. Remove the rear cover by pulling it straight away from the body of the camera.

    • Open and pivot the LCD screen to its widest open position.

    • Remove the rear cover by pulling it straight away from the body of the camera.

    • When reassembling the camera, remember to replace the screws in the same location from which you removed them. Otherwise, you may damage the camera.

    편집

  9. Now remove the top screw 3.3 mm long on the side of the camera that hold the side panels and the front cover using the #00 screwdriver. Gently remove the side panel of the camera by pulling it away form the camera.

    • Now remove the top screw 3.3 mm long on the side of the camera that hold the side panels and the front cover using the #00 screwdriver.

    • Gently remove the side panel of the camera by pulling it away form the camera.

    • The side panel may get stuck on the internal wires, so gently wiggle this panel loose.

    편집

  10. Unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel using the #00 screwdriver.

    • Unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel using the #00 screwdriver.

    편집

  11. Underneath the battery cover there is another 3.8 mm screw in the corner that needs to be removed using the #00 screwdriver.

    • Underneath the battery cover there is another 3.8 mm screw in the corner that needs to be removed using the #00 screwdriver.

    편집

  12. Gently pull up on the front cover to remove it from the body

    • Gently pull up on the front cover to remove it from the body

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 6명과 함께

Travis

회원 가입일: 2011년 01월 28일

214 평판

안내서 1개 작성함

배지: 8

배지 +5개 더

팀

Cal Poly, Team 7-31, Regan Winter 2011 Cal Poly, Team 7-31, Regan Winter 2011 회원

CPSU-REGAN-W11S7G31

6 회원들

안내서 12개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 7

전체 시간: 3,780