소개

Use this guide to replace the front panel of the camera as well as the battery door.

Place camera LCD side up and press up on the battery door. Let it swing open until you can see the battery inside.
  • Place camera LCD side up and press up on the battery door.

  • Let it swing open until you can see the battery inside.

댓글 쓰기

Press down on the orange plastic.
  • Press down on the orange plastic.

  • This will gently eject the battery from its compartment.

댓글 쓰기

Holding the edges, slide out the battery. Holding the edges, slide out the battery.
  • Holding the edges, slide out the battery.

댓글 쓰기

Look at the camera from the side with the lanyard and 4 screws.
  • Look at the camera from the side with the lanyard and 4 screws.

    • Remove the two 3.4 mm screws on the metallic colored part.

댓글 쓰기

Remove the 3mm screw on the top left.
  • Remove the 3mm screw on the top left.

    • NOTE: When reassembling, it is helpful to put the top screw back in before placing the front cover back on the camera.

  • Now remove the 5.3mm screw on the bottom.

댓글 쓰기

아버지의 날 선물 안내
아버지 뿐만 아니라 다른 분들도 존중합시다—우리에게 수리하는 법을 가르쳐 주신 모든 멘토를 축하합시다.
아버지의 날 선물 안내
우리에게 수리하는 법을 가르쳐 주신 사람들을 존중합시다.
Place the camera LCD side down.
  • Place the camera LCD side down.

  • Remove the two 5.3mm screws by the battery door.

댓글 쓰기

Remove the four 3.4mm screws on the bottom of the camera around the tripod mount.
  • Remove the four 3.4mm screws on the bottom of the camera around the tripod mount.

    • Make sure to keep these screws separate from the previous 5.3 mm screws.

댓글 쓰기

Stand the camera back up.
  • Stand the camera back up.

  • Remove the two 3.6mm screws on the side with the A/V Out port.

댓글 쓰기

Lift open the rubber flap covering the A/V Out port.
  • Lift open the rubber flap covering the A/V Out port.

    • Remove the 3.4mm screw in the center.

    • During reassembly, put the A/V out rubber door on before replacing the front panel of the camera

댓글 쓰기

Use a spudger and gently open up the front panel of the camera.
  • Use a spudger and gently open up the front panel of the camera.

    • A thin plastic ribbon will stay connected by a brown piece to front panel of the camera.

댓글 쓰기

There will be a brown plastic piece keeping the thin plastic ribbon in place.
  • There will be a brown plastic piece keeping the thin plastic ribbon in place.

  • Use the spudger to pull out the brown plastic piece attached to the orange plastic.

댓글 쓰기

Use a pair of tweezers and remove the metal piece inside the camera.
  • Use a pair of tweezers and remove the metal piece inside the camera.

댓글 쓰기

Remove the battery door
  • Remove the battery door

    • NOTE: Putting this back on requires aligning the spring on the back of the door with the hole on the camera

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Karim

회원 가입일: 2012년 04월 12일

24 평판

안내서 3개 작성하였습니다

Cal Poly, Team 7-34, Maness Spring 2012 Cal Poly, Team 7-34, Maness Spring 2012 회원

CPSU-MANESS-S12S7G34

5 회원들

안내서 6개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 5

전체 시간: 841