소개

This is a guide to removing the camera's logic board.

Unscrew five Phillips screws using a #0 Phillips screwdriver.
  • Unscrew five Phillips screws using a #0 Phillips screwdriver.

  • One screw is on upper right corner of the back panel.

  • The other four screws are on the bottom of the camera.

댓글 쓰기

Open memory card cover by moving the slide switch toward the top end of of the camera.
  • Open memory card cover by moving the slide switch toward the top end of of the camera.

  • Remove the memory card from the slot.

댓글 쓰기

  • Remove the rear cover from the rest of the camera.

  • This may require gentle rocking of the case to free it.

댓글 쓰기

  • Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

댓글 쓰기

  • Free the front cover from the rest of the camera.

  • The cover may require gentle rocking to remove.

댓글 쓰기

  • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

댓글 쓰기

  • Gently separate the top of LCD from the rest of the camera using your thumb.

  • Be careful not pull the LCD too far because of the ribbon cable connection.

  • Place the Spudger in the hole of the electrical ribbon.

  • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

  • The LCD will still be connected to the rest of the camera

댓글 쓰기

  • Unscrew single Phillips screw with a #0 Phillips screwdriver.

  • Free the bottom panel and attached ribbon from the rest of the camera.

  • Be careful not to damage the ribbon.

댓글 쓰기

  • Turn over the camera.

  • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

  • The plastic will still be connected on the left side.

댓글 쓰기

  • Place the Spudger between the orange ribbon and the black ribbon gate.

  • Lift the ribbon gate using the Spudger.

댓글 쓰기

  • Place the Spludger in the corner of the ribbon above the hole.

  • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

댓글 쓰기

  • Free this ribbon and the bottom panel from the rest of the camera.

  • Be careful not to damage the ribbon.

댓글 쓰기

  • Turn the camera over so you can see the LCD.

  • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

댓글 쓰기

  • Lift the blue ribbon gate using the Spudger.

댓글 쓰기

  • Insert the Spudger into the hole of the ribbon.

  • Move the Spudger away from the gate to fully remove ribbon.

  • Be careful not to damage the ribbon.

댓글 쓰기

  • Lift the LCD away from the rest of the camera.

댓글 쓰기

  • Lift off the capture button by wiggling it back and forth while pulling upward.

  • Be careful not to damage the two clips.

댓글 쓰기

  • Flip open the four ribbon gates using the Spudger.

  • Gently pull out the ribbon cables from the gates using the Spudger.

댓글 쓰기

  • Unscrew the four Phillips screws using a #0 Phillips screwdriver.

댓글 쓰기

  • Gently lift the the logic board.

  • Be careful not to pull too hard and damage the white ribbon cable.

  • Place the Spudger so that it is between the logic board, the white ribbon cable, and the rest of the camera.

  • Remove the white ribbon cable by pulling the Spudger away from the camera, keeping it parallel to the logic board.

댓글 쓰기

  • Lay the logic board back down so that it is resting on the body of the camera.

  • Pull the two plugs (white and green) out to the right from the logic board using the tweezers.

댓글 쓰기

  • We're now ready to begin the desoldering process. You'll need a soldering iron, solder, and desoldering wick. You should be able to find these items at a Radio Shack if you don't already have them.

  • Please do not perform this step if you are not comfortable or have previous experience with soldering. Doing so, could cause severe damage to your camera.

  • Desolder the two soldered ribbon cables attached to the logic board.

댓글 쓰기

  • Free the logic board from the rest of the camera.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Nathan Balcom

회원 가입일: 2010년 01월 21일

81 평판

안내서 8개 작성하였습니다

Cal Poly, Team 16-28, Maness Winter 2010 Cal Poly, Team 16-28, Maness Winter 2010 회원

CPSU-MANESS-W10S16G28

4 회원들

안내서 9개 작성하였습니다

How brilliant! Great pictures! But where did you buy the new logic board?

Rosario - 답글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 2

지난 30일: 3

전체 시간: 2,618