소개

This guide serves to remove and replace the motherboard.

부품

부품은 필요하지 않습니다.

  1. Remove the knot on the wrist lanyard.
    • Remove the knot on the wrist lanyard.

    • Remove the battery and memory card.

    댓글 쓰기

  2. Remove all screws from sides of outer casing.
    • Remove all screws from sides of outer casing.

    • Begin removing the screws on the bottom of the outer casing.

    • Remove the rest of the screws from the outer casing.

    댓글 쓰기

    • Gently pull the front cover off the camera.

    댓글 쓰기

    • Open the "A/V Out Digital" cover slide, and remove the screw inside.

    • Gently pull off the back casing.

    • Remove the black "L" shaped piece of metal.

    댓글 쓰기

    • Remove the three screws that are holding the screen in place and free the screen from the underlying components.

    • Be careful of the ribbon wire that is still attached on the left of the screen.

    댓글 쓰기

    • With the spudger, gently lift the black flap that is holding the wide ribbon cable wire in place.

    • Unplug the wide ribbon cable.

    • Unplug the narrow ribbon cable to free the LCD screen from the camera body

    The author failed to mention a couple things. First, the screen is in a holder which you remove, then after pulling off some electrical tape, you have to yank the actual screen out. Second, I only had two screws to pull the screen holder out, not three. Third, the thing that you have to pull to get the screen ribbon cable out is actually a tiny black hinge, so don't worry if it suddenly snaps back. Finally, to put the thing back together, it really helps if you have a tweezers to get the ribbon cables back into place.

    and fyi replacement screens available from canon parts department for about 50 bucks.

    steven - 답글

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • Remove the screws holding down function set button.

    댓글 쓰기

    • Gently pry up the tab with a metal spudger and remove the ribbon cable.

    댓글 쓰기

    • Be mindful of the pins as you lift up and remove the function/set button.

    댓글 쓰기

    • Remove the screws from the metal plate.

    • Gently remove the metal plate.

    댓글 쓰기

    • Lift the tab connecting the ribbon cable and detach.

    댓글 쓰기

    • Use a spudger to lift up the ribbon cable tab.

    • Detach the ribbon cable.

    댓글 쓰기

    • Gently remove the entire ribbon cable connection to release the ribbon cable from the camera.

    댓글 쓰기

    • Unscrew the circuit board from the flash unit.

    댓글 쓰기

    • Pry up the ribbon cable connection and remove it from the camera.

    • Lift the ribbon cable tab and completely detach the cable from the camera.

    댓글 쓰기

    • Pry up the connection, being mindful of the light adhesive.

    댓글 쓰기

    • Remove the last screw holding the motherboard to the main body.

    댓글 쓰기

    • Use a spudger to gently lift the motherboard from the camera.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

BrettH

회원 가입일: 2009년 10월 28일

219 평판

안내서 5개 작성하였습니다

Cal Poly, Team 19-5, Maness SU 2012 Cal Poly, Team 19-5, Maness SU 2012 회원

CPSU-MANESS-SU12S19G5

1 회원

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 5

전체 시간: 4,151