기기를 수리하세요 커뮤니티 상점

Canon PowerShot SD1200 IS Motherboard

소개

Use this guide to access the motherboard to reseat connections on the motherboard or to remove the motherboard for replacement.

필요한 것

  1. Canon PowerShot SD1200 IS Motherboard, Front and Rear Covers: 1 단계, 이미지 1/1

    • Remove the battery.

    편집

  2. Canon PowerShot SD1200 IS Motherboard: 2 단계, 이미지 1/3 Canon PowerShot SD1200 IS Motherboard: 2 단계, 이미지 2/3 Canon PowerShot SD1200 IS Motherboard: 2 단계, 이미지 3/3

    • Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)

    • Remove the two screws from the bottom of the camera. (4mm Phillips 00)

    • Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

    편집

  3. Canon PowerShot SD1200 IS Motherboard: 3 단계, 이미지 1/2 Canon PowerShot SD1200 IS Motherboard: 3 단계, 이미지 2/2

    • Pull off the front cover.

    • If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.

    • Remove the back cover.

    편집

  5. Canon PowerShot SD1200 IS Motherboard, Motherboard: 4 단계, 이미지 1/1

    • Remove the microphone connector by gripping it with the tool and gently, with a wiggling motion, pull it out.

    • Pull the connector straight out by the white connector. Pulling on the wires will damage them.

    편집

  6. Canon PowerShot SD1200 IS Motherboard: 5 단계, 이미지 1/1

    • Lift off the mechanical shutter button assembly.

    편집

  7. Canon PowerShot SD1200 IS Motherboard: 6 단계, 이미지 1/2 Canon PowerShot SD1200 IS Motherboard: 6 단계, 이미지 2/2

    • Use the spudger to lift the tab on the Zero Insertion Force (ZIF) connector located at the bottom of the motherboard.

    • Be sure you are prying up on the hinged retaining flap, not the connector itself.

    • Slide out the ribbon cable.

    • Use the spudger to pry up each side of the Flat-Topped Connectors

    편집

  8. Canon PowerShot SD1200 IS Motherboard: 7 단계, 이미지 1/1

    • Remove the press fit ribbon cable by prying upward with spudger tool.

    • It is not necessary to remove the Lens or Flash Assemblies to remove the motherboard.

    편집

  9. Canon PowerShot SD1200 IS Motherboard: 8 단계, 이미지 1/1

    • Remove the bottom right screw from the motherboard. (4mm Phillips 00)

    • Remove top and lower left black screws from the motherboard. (2.5mm Phillips 00)

    편집

  10. Canon PowerShot SD1200 IS Motherboard: 9 단계, 이미지 1/1

    • Lift out the motherboard.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Jeff Casper

회원 가입일: 09/15/16

848 평판

안내서 7개 작성하였습니다

배지: 18

배지 +15개 더

팀

USF Tampa, Team 17-5, Blackwell Fall 2016 USF Tampa, Team 17-5, Blackwell Fall 2016 회원

USFT-BLACKWELL-F16S17G5

3 회원들

안내서 7개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 1

30일 전: 14

전체 시간: 394