기기를 수리하세요

수리할 권리

상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Canon PowerShot SD850 IS Function Set Button Replacement

작성자 iDeleted (또 다른 기여자 6명)

댓글 0
즐겨찾기 0

Canon PowerShot SD850 IS Function Set Button Replacement

난이도

보통

단계

11

소요 시간

시간 제안??

소개

This manual is for replacing the function/set button located on the back of the camera.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

1 단계 Battery

Using your fingernail, slide the light gray tab towards edge of camera.

Slide the light gray door and pull up to open the door.

In the camera shown in the photos, there is not a Memory Card or Battery.

Using your fingernail, slide the light gray tab towards edge of camera.
Slide the light gray door and pull up to open the door.
In the camera shown in the photos, there is not a Memory Card or Battery.
Both Battery and Memory Card slots should be visible.

2 단계

Use your fingernail and slide the small brown tab towards the edge of the camera.

The battery will pop up.

Use your fingernail and slide the small brown tab towards the edge of the camera.
The battery will pop up.
Pull battery straight out of battery holder.
When putting the battery back in, make sure it the battery is oriented so the terminals connect.

3 단계 Case

Remove the following 4 screws:

Two 2.8 mm Phillips #00 at the bottom of the camera.

Remove the following 4 screws:
Two 2.8 mm Phillips #00 at the bottom of the camera.
Two 2.75 mm Phillips #00 on the opposite side of the wrist strap.

4 단계

Open the A/V OUT DIGITAL flap on the side of the wrist strap.

Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap.

Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap.

Open the A/V OUT DIGITAL flap on the side of the wrist strap.
Remove the 2.75 mm Phillips #00 under the A/V OUT DIGITAL flap on the side of the wrist strap.

5 단계

On the bottom of the camera, use your fingernail to slide the light gray tab towards the edge of the camera.

Slide light gray door and pull up to open the door.

On the bottom of the camera, use your fingernail to slide the light gray tab towards the edge of the camera.
Slide light gray door and pull up to open the door.
Remove the 8.35 mm Phillips #00 next to the brown tab that holds the battery.

6 단계

Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera.

Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera.

Gently pull the front cover straight out from the camera. This will expose the wiring on the front of the camera.

7 단계

Remove the 2.75 mm Phillips #00 next to A/V OUT DIGITAL.

Remove the 2.75 mm Phillips #00 next to A/V OUT DIGITAL.

8 단계

Slide the back casing (with the screen protector) off to reveal the LCD and back wiring.

Slide the back casing (with the screen protector) off to reveal the LCD and back wiring.

9 단계 Function Set Button

Identify and remove the plastic function set button. Do this by gently prying up as indicated in the photo.

Identify and remove the plastic function set button. Do this by gently prying up as indicated in the photo.

Identify and remove the plastic function set button. Do this by gently prying up as indicated in the photo.

10 단계

Lift the function set button ribbon cable from the two guide pins.

Lift the function set button ribbon cable from the two guide pins.

11 단계

Remove the ribbon cable by lifting on the flat tab and pulling the ribbon cable from the connection.

Remove the ribbon cable by lifting on the flat tab and pulling the ribbon cable from the connection.

결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 6명과 함께

iDeleted

회원 가입일: 2010년 07월 07일

2,101 평판

안내서 39개 작성하였습니다

배지 +6개 더

댓글 0개

의견 추가하세요

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 9

전체 시간: 1,043