기기를 수리하세요 커뮤니티 상점

Canon PowerShot SX260 HS Flash Assembly Replacement

필요한 것

  1. Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: 1 단계, 이미지 1/3 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: 1 단계, 이미지 2/3 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: 1 단계, 이미지 3/3

    • Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.

    • The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.

    • Remove the 2 screws on the left side.

    • Remove the 2 screws on the bottom of the camera.

    • Remove the 2 screws on the right side of the camera.

    편집

  2. Canon PowerShot SX260 HS Flash Assembly Replacement: 2 단계, 이미지 1/1

    • Use your plastic opening tool to gently lift and remove the back face plate.

    편집

  3. Canon PowerShot SX260 HS Flash Assembly Replacement: 3 단계, 이미지 1/1

    • After removing the exterior screws, use your fingers to gently lift off the front face plate.

    편집

  4. Canon PowerShot SX260 HS Flash Assembly Replacement: 4 단계, 이미지 1/1

    • Next, remove the 2 (3 mm) interior screws on the left side of the camera.

    편집

  6. Canon PowerShot SX260 HS Flash Assembly Replacement: 5 단계, 이미지 1/1

    • After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

    편집

  7. Canon PowerShot SX260 HS Flash Assembly Replacement: 6 단계, 이미지 1/1

    • Next, you will need to remove the dial panel by removing the 2 (3mm) screws on the back side of the camera.

    • Gently remove the dial panel with your fingers.

    편집

  8. Canon PowerShot SX260 HS Flash Assembly Replacement: 7 단계, 이미지 1/2 Canon PowerShot SX260 HS Flash Assembly Replacement: 7 단계, 이미지 2/2

    • Remove 1 (3 mm) screw from the flash generator with a Phillips screw driver

    • Gently lift the flash generator off of the camera with the plastic opening tool .

    편집

  9. Canon PowerShot SX260 HS Flash Assembly Replacement: 8 단계, 이미지 1/1

    • Gently unplug the ribbon cable with your tweezers.

    • Be careful not to rip it.

    편집

  10. Canon PowerShot SX260 HS Flash Assembly Replacement: 9 단계, 이미지 1/2 Canon PowerShot SX260 HS Flash Assembly Replacement: 9 단계, 이미지 2/2

    • Using your plastic opening tool to gently move the plug lock from the end of the ribbon cord by lifting it upward.

    • Gently remove the ribbon cable from the connector with tweezers.

    편집

  11. Canon PowerShot SX260 HS Flash Assembly Replacement: 10 단계, 이미지 1/2 Canon PowerShot SX260 HS Flash Assembly Replacement: 10 단계, 이미지 2/2

    • Gently remove the ribbon cable assembly from the top of the camera with your tweezers.

    • This cable is a long piece that runs across the top of the camera.

    • The flash assembly is connected to this cable.

    • Once removed gently lift out of the camera

    • Replace the ribbon cable with the attached flash assembly.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Tyler Kelch

회원 가입일: 03/05/15

622 평판

안내서 4개 작성하였습니다

배지: 8

배지 +5개 더

팀

Sam Houston State, Team 11-8, Blackburne Winter 2015 Sam Houston State, Team 11-8, Blackburne Winter 2015 회원

SHSU-BLACKBURNE-W15S11G8

2 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 16

전체 시간: 1,651